rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c
index 44d44fe..2451bef 100644
--- a/common/cmd_eeprom.c
+++ b/common/cmd_eeprom.c
@@ -32,8 +32,8 @@
* Use the following configuration options to ensure no unneeded performance
* degradation (typical for EEPROM) is incured for FRAM memory:
*
- * #define CFG_I2C_FRAM
- * #undef CFG_EEPROM_PAGE_WRITE_DELAY_MS
+ * #define CONFIG_SYS_I2C_FRAM
+ * #undef CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
*
*/
@@ -47,12 +47,12 @@
uchar *buffer, unsigned cnt);
extern int eeprom_write (unsigned dev_addr, unsigned offset,
uchar *buffer, unsigned cnt);
-#if defined(CFG_EEPROM_WREN)
+#if defined(CONFIG_SYS_EEPROM_WREN)
extern int eeprom_write_enable (unsigned dev_addr, int state);
#endif
-#if defined(CFG_EEPROM_X40430)
+#if defined(CONFIG_SYS_EEPROM_X40430)
/* Maximum number of times to poll for acknowledge after write */
#define MAX_ACKNOWLEDGE_POLLS 10
#endif
@@ -65,7 +65,7 @@
const char *const fmt =
"\nEEPROM @0x%lX %s: addr %08lx off %04lx count %ld ... ";
-#if defined(CFG_I2C_MULTI_EEPROMS)
+#if defined(CONFIG_SYS_I2C_MULTI_EEPROMS)
if (argc == 6) {
ulong dev_addr = simple_strtoul (argv[2], NULL, 16);
ulong addr = simple_strtoul (argv[3], NULL, 16);
@@ -73,11 +73,11 @@
ulong cnt = simple_strtoul (argv[5], NULL, 16);
#else
if (argc == 5) {
- ulong dev_addr = CFG_DEF_EEPROM_ADDR;
+ ulong dev_addr = CONFIG_SYS_DEF_EEPROM_ADDR;
ulong addr = simple_strtoul (argv[2], NULL, 16);
ulong off = simple_strtoul (argv[3], NULL, 16);
ulong cnt = simple_strtoul (argv[4], NULL, 16);
-#endif /* CFG_I2C_MULTI_EEPROMS */
+#endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
# ifndef CONFIG_SPI
eeprom_init ();
@@ -111,16 +111,16 @@
/*-----------------------------------------------------------------------
*
- * for CFG_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
+ * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
* 0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
*
- * for CFG_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
+ * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
* 0x00000nxx for EEPROM address selectors and page number at n.
*/
#ifndef CONFIG_SPI
-#if !defined(CFG_I2C_EEPROM_ADDR_LEN) || CFG_I2C_EEPROM_ADDR_LEN < 1 || CFG_I2C_EEPROM_ADDR_LEN > 2
-#error CFG_I2C_EEPROM_ADDR_LEN must be 1 or 2
+#if !defined(CONFIG_SYS_I2C_EEPROM_ADDR_LEN) || CONFIG_SYS_I2C_EEPROM_ADDR_LEN < 1 || CONFIG_SYS_I2C_EEPROM_ADDR_LEN > 2
+#error CONFIG_SYS_I2C_EEPROM_ADDR_LEN must be 1 or 2
#endif
#endif
@@ -136,11 +136,11 @@
*/
while (offset < end) {
unsigned alen, len;
-#if !defined(CFG_I2C_FRAM)
+#if !defined(CONFIG_SYS_I2C_FRAM)
unsigned maxlen;
#endif
-#if CFG_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
+#if CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
uchar addr[2];
blk_off = offset & 0xFF; /* block offset */
@@ -157,7 +157,7 @@
addr[1] = offset >> 8; /* upper address octet */
addr[2] = blk_off; /* lower address octet */
alen = 3;
-#endif /* CFG_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
+#endif /* CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
addr[0] |= dev_addr; /* insert device address */
@@ -168,7 +168,7 @@
* bytes that can be ccessed with the single read or write
* operation.
*/
-#if !defined(CFG_I2C_FRAM)
+#if !defined(CONFIG_SYS_I2C_FRAM)
maxlen = 0x100 - blk_off;
if (maxlen > I2C_RXTX_LEN)
maxlen = I2C_RXTX_LEN;
@@ -191,10 +191,10 @@
/*-----------------------------------------------------------------------
*
- * for CFG_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
+ * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
* 0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
*
- * for CFG_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
+ * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
* 0x00000nxx for EEPROM address selectors and page number at n.
*/
@@ -204,7 +204,7 @@
unsigned blk_off;
int rcode = 0;
-#if defined(CFG_EEPROM_X40430)
+#if defined(CONFIG_SYS_EEPROM_X40430)
uchar contr_r_addr[2];
uchar addr_void[2];
uchar contr_reg[2];
@@ -212,7 +212,7 @@
int i;
#endif
-#if defined(CFG_EEPROM_WREN)
+#if defined(CONFIG_SYS_EEPROM_WREN)
eeprom_write_enable (dev_addr,1);
#endif
/* Write data until done or would cross a write page boundary.
@@ -222,11 +222,11 @@
while (offset < end) {
unsigned alen, len;
-#if !defined(CFG_I2C_FRAM)
+#if !defined(CONFIG_SYS_I2C_FRAM)
unsigned maxlen;
#endif
-#if CFG_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
+#if CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
uchar addr[2];
blk_off = offset & 0xFF; /* block offset */
@@ -243,7 +243,7 @@
addr[1] = offset >> 8; /* upper address octet */
addr[2] = blk_off; /* lower address octet */
alen = 3;
-#endif /* CFG_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
+#endif /* CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
addr[0] |= dev_addr; /* insert device address */
@@ -254,11 +254,11 @@
* bytes that can be ccessed with the single read or write
* operation.
*/
-#if !defined(CFG_I2C_FRAM)
+#if !defined(CONFIG_SYS_I2C_FRAM)
-#if defined(CFG_EEPROM_PAGE_WRITE_BITS)
+#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_BITS)
-#define EEPROM_PAGE_SIZE (1 << CFG_EEPROM_PAGE_WRITE_BITS)
+#define EEPROM_PAGE_SIZE (1 << CONFIG_SYS_EEPROM_PAGE_WRITE_BITS)
#define EEPROM_PAGE_OFFSET(x) ((x) & (EEPROM_PAGE_SIZE - 1))
maxlen = EEPROM_PAGE_SIZE - EEPROM_PAGE_OFFSET(blk_off);
@@ -275,7 +275,7 @@
#ifdef CONFIG_SPI
spi_write (addr, alen, buffer, len);
#else
-#if defined(CFG_EEPROM_X40430)
+#if defined(CONFIG_SYS_EEPROM_X40430)
/* Get the value of the control register.
* Set current address (internal pointer in the x40430)
* to 0x1ff.
@@ -284,9 +284,9 @@
contr_r_addr[1] = 0xff;
addr_void[0] = 0;
addr_void[1] = addr[1];
-#ifdef CFG_I2C_EEPROM_ADDR
- contr_r_addr[0] |= CFG_I2C_EEPROM_ADDR;
- addr_void[0] |= CFG_I2C_EEPROM_ADDR;
+#ifdef CONFIG_SYS_I2C_EEPROM_ADDR
+ contr_r_addr[0] |= CONFIG_SYS_I2C_EEPROM_ADDR;
+ addr_void[0] |= CONFIG_SYS_I2C_EEPROM_ADDR;
#endif
contr_reg[0] = 0xff;
if (i2c_read (contr_r_addr[0], contr_r_addr[1], 1, contr_reg, 1) != 0) {
@@ -334,8 +334,8 @@
for (i = 0; i < MAX_ACKNOWLEDGE_POLLS; i++) {
if (i2c_read (addr_void[0], addr_void[1], 1, contr_reg, 1) == 0)
break; /* got ack */
-#if defined(CFG_EEPROM_PAGE_WRITE_DELAY_MS)
- udelay(CFG_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
+#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
+ udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
#endif
}
if (i == MAX_ACKNOWLEDGE_POLLS) {
@@ -364,11 +364,11 @@
buffer += len;
offset += len;
-#if defined(CFG_EEPROM_PAGE_WRITE_DELAY_MS)
- udelay(CFG_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
+#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
+ udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
#endif
}
-#if defined(CFG_EEPROM_WREN)
+#if defined(CONFIG_SYS_EEPROM_WREN)
eeprom_write_enable (dev_addr,0);
#endif
return rcode;
@@ -382,11 +382,11 @@
/* Probe the chip address
*/
-#if CFG_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
+#if CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 && !defined(CONFIG_SPI_X)
chip = offset >> 8; /* block number */
#else
chip = offset >> 16; /* block number */
-#endif /* CFG_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
+#endif /* CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SPI_X */
chip |= dev_addr; /* insert device address */
@@ -397,12 +397,12 @@
/*-----------------------------------------------------------------------
* Set default values
*/
-#ifndef CFG_I2C_SPEED
-#define CFG_I2C_SPEED 50000
+#ifndef CONFIG_SYS_I2C_SPEED
+#define CONFIG_SYS_I2C_SPEED 50000
#endif
-#ifndef CFG_I2C_SLAVE
-#define CFG_I2C_SLAVE 0xFE
+#ifndef CONFIG_SYS_I2C_SLAVE
+#define CONFIG_SYS_I2C_SLAVE 0xFE
#endif
void eeprom_init (void)
@@ -412,7 +412,7 @@
#endif
#if defined(CONFIG_HARD_I2C) || \
defined(CONFIG_SOFT_I2C)
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
}
/*-----------------------------------------------------------------------
@@ -422,7 +422,7 @@
#if defined(CONFIG_CMD_EEPROM)
-#ifdef CFG_I2C_MULTI_EEPROMS
+#ifdef CONFIG_SYS_I2C_MULTI_EEPROMS
U_BOOT_CMD(
eeprom, 6, 1, do_eeprom,
"eeprom - EEPROM sub-system\n",
@@ -438,6 +438,6 @@
"eeprom write addr off cnt\n"
" - read/write `cnt' bytes at EEPROM offset `off'\n"
);
-#endif /* CFG_I2C_MULTI_EEPROMS */
+#endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
#endif