rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/board/lwmon5/config.mk b/board/lwmon5/config.mk
index bf2b879..3c6d041 100644
--- a/board/lwmon5/config.mk
+++ b/board/lwmon5/config.mk
@@ -35,5 +35,5 @@
endif
ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
endif
diff --git a/board/lwmon5/init.S b/board/lwmon5/init.S
index 5aade72..718cec6 100644
--- a/board/lwmon5/init.S
+++ b/board/lwmon5/init.S
@@ -47,7 +47,7 @@
* BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
* speed up boot process. It is patched after relocation to enable SA_I
*/
- tlbentry(CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G)
+ tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G)
/*
* TLB entries for SDRAM are not needed on this platform.
@@ -55,28 +55,28 @@
* routine.
*/
-#ifdef CFG_INIT_RAM_DCACHE
+#ifdef CONFIG_SYS_INIT_RAM_DCACHE
/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
- tlbentry(CFG_INIT_RAM_ADDR, SZ_4K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G)
+ tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G)
#endif
/* TLB-entry for PCI Memory */
- tlbentry(CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I)
- tlbentry(CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I)
/* TLB-entry for the FPGA Chip select 2 */
- tlbentry(CFG_FPGA_BASE_0, SZ_1M, CFG_FPGA_BASE_0, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+ tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
/* TLB-entry for the FPGA Chip select 3 */
- tlbentry(CFG_FPGA_BASE_1, SZ_1M, CFG_FPGA_BASE_1, 1,AC_R|AC_W|AC_X|SA_I|SA_G)
+ tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_R|AC_W|AC_X|SA_I|SA_G)
/* TLB-entry for the LIME Controller */
- tlbentry(CFG_LIME_BASE_0, SZ_16M, CFG_LIME_BASE_0, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
- tlbentry(CFG_LIME_BASE_1, SZ_16M, CFG_LIME_BASE_1, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
- tlbentry(CFG_LIME_BASE_2, SZ_16M, CFG_LIME_BASE_2, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
- tlbentry(CFG_LIME_BASE_3, SZ_16M, CFG_LIME_BASE_3, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_R|AC_W|AC_X|SA_I|SA_G)
/* TLB-entry for Internal Registers & OCM */
tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0, AC_R|AC_W|AC_X|SA_I)
diff --git a/board/lwmon5/kbd.c b/board/lwmon5/kbd.c
index 1e5349a..0a8787a 100644
--- a/board/lwmon5/kbd.c
+++ b/board/lwmon5/kbd.c
@@ -74,7 +74,7 @@
/* maximum number of "magic" key codes that can be assigned */
-static uchar kbd_addr = CFG_I2C_KEYBD_ADDR;
+static uchar kbd_addr = CONFIG_SYS_I2C_KEYBD_ADDR;
static uchar *key_match (uchar *);
@@ -106,7 +106,7 @@
uchar val, errcd;
int i;
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
gd->kbd_status = 0;
@@ -412,7 +412,7 @@
int i;
#if 0 /* Done in kbd_init */
- i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
/* Read keys */
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index 8975bfd..aa62f37 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -27,7 +27,7 @@
DECLARE_GLOBAL_DATA_PTR;
-extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
+extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
ulong flash_get_size(ulong base, int banknum);
int misc_init_r_kbd(void);
@@ -94,24 +94,24 @@
reg = 0;
mtsdr(sdr_pci0, 0x00000000 | reg);
- gpio_write_bit(CFG_GPIO_FLASH_WP, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_FLASH_WP, 1);
-#if CONFIG_POST & CFG_POST_BSPEC1
- gpio_write_bit(CFG_GPIO_HIGHSIDE, 1);
+#if CONFIG_POST & CONFIG_SYS_POST_BSPEC1
+ gpio_write_bit(CONFIG_SYS_GPIO_HIGHSIDE, 1);
reg = 0; /* reuse as counter */
- out_be32((void *)CFG_DSPIC_TEST_ADDR,
- in_be32((void *)CFG_DSPIC_TEST_ADDR)
- & ~CFG_DSPIC_TEST_MASK);
- while (!gpio_read_in_bit(CFG_GPIO_DSPIC_READY) && reg++ < 1000) {
+ out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR,
+ in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR)
+ & ~CONFIG_SYS_DSPIC_TEST_MASK);
+ while (!gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY) && reg++ < 1000) {
udelay(1000);
}
- gpio_write_bit(CFG_GPIO_HIGHSIDE, 0);
- if (gpio_read_in_bit(CFG_GPIO_DSPIC_READY)) {
+ gpio_write_bit(CONFIG_SYS_GPIO_HIGHSIDE, 0);
+ if (gpio_read_in_bit(CONFIG_SYS_GPIO_DSPIC_READY)) {
/* set "boot error" flag */
- out_be32((void *)CFG_DSPIC_TEST_ADDR,
- in_be32((void *)CFG_DSPIC_TEST_ADDR) |
- CFG_DSPIC_TEST_MASK);
+ out_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR,
+ in_be32((void *)CONFIG_SYS_DSPIC_TEST_ADDR) |
+ CONFIG_SYS_DSPIC_TEST_MASK);
}
#endif
@@ -123,14 +123,14 @@
* MDIO address. A 2nd reset at this time will make sure, that the
* correct address is latched.
*/
- gpio_write_bit(CFG_GPIO_PHY0_RST, 1);
- gpio_write_bit(CFG_GPIO_PHY1_RST, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_PHY0_RST, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_PHY1_RST, 1);
udelay(1000);
- gpio_write_bit(CFG_GPIO_PHY0_RST, 0);
- gpio_write_bit(CFG_GPIO_PHY1_RST, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_PHY0_RST, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_PHY1_RST, 0);
udelay(1000);
- gpio_write_bit(CFG_GPIO_PHY0_RST, 1);
- gpio_write_bit(CFG_GPIO_PHY1_RST, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_PHY0_RST, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_PHY1_RST, 1);
return 0;
}
@@ -194,7 +194,7 @@
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
- -CFG_MONITOR_LEN,
+ -CONFIG_SYS_MONITOR_LEN,
0xffffffff,
&flash_info[1]);
@@ -338,7 +338,7 @@
* may not be sufficient for a given board.
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
/*--------------------------------------------------------------------------+
@@ -352,14 +352,14 @@
| Make this region non-prefetchable.
+--------------------------------------------------------------------------*/
out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */
+ out32r(PCIX0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
+ out32r(PCIX0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */
+ out32r(PCIX0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
+ out32r(PCIX0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
@@ -374,8 +374,8 @@
/* Program the board's subsystem id/vendor id */
pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CFG_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
+ CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
/* Configure command register as bus master */
pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
@@ -389,13 +389,13 @@
pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
/*************************************************************************
* pci_master_init
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
+#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
unsigned short temp_short;
@@ -410,7 +410,7 @@
temp_short | PCI_COMMAND_MASTER |
PCI_COMMAND_MEMORY);
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */
+#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
/*************************************************************************
* is_pci_host
@@ -460,8 +460,8 @@
/*
* Toggle watchdog output
*/
- val = gpio_read_out_bit(CFG_GPIO_WATCHDOG) == 0 ? 1 : 0;
- gpio_write_bit(CFG_GPIO_WATCHDOG, val);
+ val = gpio_read_out_bit(CONFIG_SYS_GPIO_WATCHDOG) == 0 ? 1 : 0;
+ gpio_write_bit(CONFIG_SYS_GPIO_WATCHDOG, val);
}
int do_eeprom_wp(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
@@ -472,9 +472,9 @@
}
if ((strcmp(argv[1], "on") == 0)) {
- gpio_write_bit(CFG_GPIO_EEPROM_EXT_WP, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_EEPROM_EXT_WP, 1);
} else if ((strcmp(argv[1], "off") == 0)) {
- gpio_write_bit(CFG_GPIO_EEPROM_EXT_WP, 0);
+ gpio_write_bit(CONFIG_SYS_GPIO_EEPROM_EXT_WP, 0);
} else {
printf("Usage:\n%s\n", cmdtp->usage);
return 1;
@@ -528,23 +528,23 @@
/*
* Reset Lime controller
*/
- gpio_write_bit(CFG_GPIO_LIME_S, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_LIME_S, 1);
udelay(500);
- gpio_write_bit(CFG_GPIO_LIME_RST, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_LIME_RST, 1);
/* Lime memory clock adjusted to 100MHz */
- out_be32((void *)CFG_LIME_SDRAM_CLOCK, CFG_LIME_CLOCK_100MHZ);
+ out_be32((void *)CONFIG_SYS_LIME_SDRAM_CLOCK, CONFIG_SYS_LIME_CLOCK_100MHZ);
/* Wait untill time expired. Because of requirements in lime manual */
udelay(300);
/* Write lime controller memory parameters */
- out_be32((void *)CFG_LIME_MMR, CFG_LIME_MMR_VALUE);
+ out_be32((void *)CONFIG_SYS_LIME_MMR, CONFIG_SYS_LIME_MMR_VALUE);
mb862xx.winSizeX = 640;
mb862xx.winSizeY = 480;
mb862xx.gdfBytesPP = 2;
mb862xx.gdfIndex = GDF_15BIT_555RGB;
- return CFG_LIME_BASE_0;
+ return CONFIG_SYS_LIME_BASE_0;
}
#define DEFAULT_BRIGHTNESS 0x64
@@ -553,12 +553,12 @@
{
if (brightness > 0) {
/* pwm duty, lamp on */
- out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000024), brightness);
- out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000020), 0x701);
+ out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000024), brightness);
+ out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000020), 0x701);
} else {
/* lamp off */
- out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000024), 0x00);
- out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000020), 0x00);
+ out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000024), 0x00);
+ out_be32((void *)(CONFIG_SYS_FPGA_BASE_0 + 0x00000020), 0x00);
}
}
@@ -595,5 +595,5 @@
void board_reset(void)
{
- gpio_write_bit(CFG_GPIO_BOARD_RESET, 1);
+ gpio_write_bit(CONFIG_SYS_GPIO_BOARD_RESET, 1);
}
diff --git a/board/lwmon5/sdram.c b/board/lwmon5/sdram.c
index 189e824..72968d7 100644
--- a/board/lwmon5/sdram.c
+++ b/board/lwmon5/sdram.c
@@ -45,10 +45,10 @@
* memory.
*
* If at some time this restriction doesn't apply anymore, just define
- * CFG_ENABLE_SDRAM_CACHE in the board config file and this code should setup
+ * CONFIG_SYS_ENABLE_SDRAM_CACHE in the board config file and this code should setup
* everything correctly.
*/
-#ifdef CFG_ENABLE_SDRAM_CACHE
+#ifdef CONFIG_SYS_ENABLE_SDRAM_CACHE
#define MY_TLB_WORD2_I_ENABLE 0 /* enable caching on SDRAM */
#else
#define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */
@@ -116,7 +116,7 @@
* Because of 440EPx errata CHIP 11, we don't touch the last 256
* bytes of SDRAM.
*/
- bytes_remaining = num_bytes - CFG_MEM_TOP_HIDE;
+ bytes_remaining = num_bytes - CONFIG_SYS_MEM_TOP_HIDE;
/*
* We have to write the ECC bytes by zeroing and flushing in smaller
@@ -252,29 +252,29 @@
/* -----------------------------------------------------------+
* Perform data eye search if requested.
* ----------------------------------------------------------*/
- program_tlb(0, CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20,
+ program_tlb(0, CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20,
TLB_WORD2_I_ENABLE);
denali_core_search_data_eye();
- remove_tlb(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20);
+ remove_tlb(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20);
#endif
/*
* Program tlb entries for this size (dynamic)
*/
- program_tlb(0, CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20,
+ program_tlb(0, CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MBYTES_SDRAM << 20,
MY_TLB_WORD2_I_ENABLE);
/*
* Setup 2nd TLB with same physical address but different virtual address
* with cache enabled. This is done for fast ECC generation.
*/
- program_tlb(0, CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20, 0);
+ program_tlb(0, CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20, 0);
#ifdef CONFIG_DDR_ECC
/*
* If ECC is enabled, initialize the parity bits.
*/
- program_ecc(CFG_DDR_CACHED_ADDR, CFG_MBYTES_SDRAM << 20, 0);
+ program_ecc(CONFIG_SYS_DDR_CACHED_ADDR, CONFIG_SYS_MBYTES_SDRAM << 20, 0);
#endif
/*
@@ -284,5 +284,5 @@
*/
set_mcsr(get_mcsr());
- return (CFG_MBYTES_SDRAM << 20);
+ return (CONFIG_SYS_MBYTES_SDRAM << 20);
}
diff --git a/board/lwmon5/u-boot.lds b/board/lwmon5/u-boot.lds
index b20fb1c..3cfec83 100644
--- a/board/lwmon5/u-boot.lds
+++ b/board/lwmon5/u-boot.lds
@@ -137,7 +137,7 @@
*(COMMON)
}
- ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified.");
+ ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_LEN and TEXT_BASE may need to be modified.");
_end = . ;
PROVIDE (end = .);