diff --git a/board/freescale/t102xrdb/MAINTAINERS b/board/freescale/t102xrdb/MAINTAINERS
index dc554d4..297e63a 100644
--- a/board/freescale/t102xrdb/MAINTAINERS
+++ b/board/freescale/t102xrdb/MAINTAINERS
@@ -8,3 +8,8 @@
 F:	configs/T1024RDB_SDCARD_defconfig
 F:	configs/T1024RDB_SPIFLASH_defconfig
 F:	configs/T1024RDB_SECURE_BOOT_defconfig
+F:	configs/T1023RDB_defconfig
+F:	configs/T1023RDB_NAND_defconfig
+F:	configs/T1023RDB_SDCARD_defconfig
+F:	configs/T1023RDB_SPIFLASH_defconfig
+F:	configs/T1023RDB_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile
index a0cf8f6..0520066 100644
--- a/board/freescale/t102xrdb/Makefile
+++ b/board/freescale/t102xrdb/Makefile
@@ -8,7 +8,7 @@
 obj-y += spl.o
 else
 obj-y   += t102xrdb.o
-obj-y   += cpld.o
+obj-$(CONFIG_T1024RDB)   += cpld.o
 obj-y   += eth_t102xrdb.o
 obj-$(CONFIG_PCI)       += pci.o
 endif
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
index 2b17f50..922450e 100644
--- a/board/freescale/t102xrdb/README
+++ b/board/freescale/t102xrdb/README
@@ -98,6 +98,30 @@
      - Four I2C ports
 
 
+T1023RDB board Overview
+-----------------------
+- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
+- CoreNet fabric supporting coherent and noncoherent transactions with
+  prioritization and bandwidth allocation
+- SDRAM memory: 2GB Micron MT40A512M8HX unbuffered 32-bit DDR4 w/o ECC
+- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
+- Ethernet interfaces:
+  - one 1G RGMII port on-board(RTL8211FS PHY)
+  - one 1G SGMII port on-board(RTL8211FS PHY)
+  - one 2.5G SGMII port on-board(AQR105 PHY)
+- PCIe: Two Mini-PCIe connectors on-board.
+- SerDes: 4 lanes up to 10.3125GHz
+- NOR:  128MB S29GL01GS110TFIV10 Spansion NOR Flash
+- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
+- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
+- USB: one Type-A USB 2.0 port with internal PHY
+- eSDHC: support SD/MMC and eMMC card
+- 256Kbit M24256 I2C EEPROM
+- RTC: Real-time clock DS1339U on I2C bus
+- UART: one serial port on-board with RJ45 connector
+- Debugging: JTAG/COP for T1023 debugging
+
+
 Memory map on T1024RDB
 ----------------------
 Start Address  End Address      Description			Size
@@ -117,29 +141,39 @@
 0x0_0000_0000  0x0_ffff_ffff    DDR				4GB
 
 
-128MB NOR Flash memory Map
---------------------------
+128MB NOR Flash Memory Layout
+-----------------------------
 Start Address   End Address     Definition			Max size
 0xEFF40000      0xEFFFFFFF      u-boot (current bank)		768KB
 0xEFF20000      0xEFF3FFFF      u-boot env (current bank)	128KB
 0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)	128KB
 0xEFE00000      0xEFE3FFFF      QE firmware (current bank)	256KB
-0xED300000      0xEFEFFFFF      rootfs (alt bank)		44MB
+0xED300000      0xEFDFFFFF      rootfs (alt bank)		44MB
+0xED000000      0xED2FFFFF      Guest image #3 (alternate bank) 3MB
+0xECD00000      0xECFFFFFF      Guest image #2 (alternate bank) 3MB
+0xECA00000	0xECCFFFFF	Guest image #1 (alternate bank) 3MB
+0xEC900000	0xEC9FFFFF	HV config device tree(alt bank)	1MB
 0xEC800000      0xEC8FFFFF      Hardware device tree (alt bank) 1MB
-0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)		7MB + 875KB
+0xEC700000	0xEC7FFFFF	HV.uImage (alternate bank)	1MB
+0xEC020000      0xEC6FFFFF      Linux.uImage (alt bank)		~7MB
 0xEC000000      0xEC01FFFF      RCW (alt bank)			128KB
 0xEBF40000      0xEBFFFFFF      u-boot (alt bank)		768KB
 0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)		128KB
 0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)		128KB
 0xEBE00000      0xEBE3FFFF      QE firmware (alt bank)		256KB
-0xE9300000      0xEBEFFFFF      rootfs (current bank)		44MB
+0xE9300000      0xEBDFFFFF      rootfs (current bank)		44MB
+0xE9000000      0xE92FFFFF      Guest image #3 (current bank)   3MB
+0xE8D00000      0xE8FFFFFF      Guest image #2 (current bank)   3MB
+0xE8A00000	0xE8CFFFFF	Guest image #1 (current bank)	3MB
+0xE8900000	0xE89FFFFF	HV config device tree(cur bank) 1MB
 0xE8800000      0xE88FFFFF      Hardware device tree (cur bank) 1MB
-0xE8020000      0xE86FFFFF      Linux.uImage (current bank)	7MB + 875KB
+0xE8700000	0xE87FFFFF	HV.uImage (current bank)	1MB
+0xE8020000      0xE86FFFFF      Linux.uImage (current bank)	~7MB
 0xE8000000      0xE801FFFF      RCW (current bank)		128KB
 
 
-T1024 Clock frequency
----------------------
+T1024/T1023 Clock frequency
+---------------------------
 BIN   Core     DDR       Platform  FMan
 Bin1: 1400MHz  1600MT/s  400MHz    700MHz
 Bin2: 1200MHz  1600MT/s  400MHz    600MHz
@@ -155,16 +189,27 @@
    b. program u-boot.bin image to NOR flash
 	=> tftp 1000000 u-boot.bin
 	=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
-	set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+	on T1024RDB:
+	   set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+	on T1023RDB:
+	   set SW1[1:8] = '00010110', SW2[1] = '0', SW3[4] = '0' for NOR boot
 
    Switching between default bank0 and alternate bank4 on NOR flash
    To change boot source to vbank4:
-        via software:   run command 'cpld reset altbank' in u-boot.
-        via DIP-switch: set SW3[5:7] = '100'
+   on T1024RDB:
+	via software:   run command 'cpld reset altbank' in u-boot.
+	via DIP-switch: set SW3[5:7] = '100'
+   on T1023RDB:
+	via software:   run command 'gpio vbank4' in u-boot.
+	via DIP-switch: set SW3[5:7] = '100'
 
    To change boot source to vbank0:
-        via software:   run command 'cpld reset' in u-boot.
-        via DIP-Switch: set SW3[5:7] = '000'
+   on T1024RDB:
+	via software:   run command 'cpld reset' in u-boot.
+	via DIP-Switch: set SW3[5:7] = '000'
+   on T1023RDB:
+	via software:   run command 'gpio vbank0' in u-boot.
+	via DIP-switch: set SW3[5:7] = '000'
 
 2. NAND Boot:
    a. build PBL image for NAND boot
@@ -183,8 +228,11 @@
    b. program u-boot-with-spl-pbl.bin to SPI flash
 	=> tftp 1000000 u-boot-with-spl-pbl.bin
 	=> sf probe 0
-	=> sf erase 0 f0000
+	=> sf erase 0 100000
 	=> sf write 1000000 0 $filesize
+	=> tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+	=> sf erase 100000 100000
+	=> sf write 1000000 110000 20000
 	set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
 
 4. SD Boot:
@@ -236,23 +284,34 @@
 0x200000	0x27FFFF	QE Firmware	512KB(1 block)
 
 
+NAND Flash memory Map on T1023RDB
+----------------------------------------------------
+Start		End		Definition	Size
+0x000000	0x0FFFFF	u-boot		1MB
+0x100000	0x15FFFF	u-boot env	8KB
+0x160000	0x17FFFF	FMAN Ucode	128KB
+
+
 SD Card memory Map on T1024RDB
 ----------------------------------------------------
 Block		#blocks		Definition	Size
 0x008		2048		u-boot img	1MB
 0x800		0016		u-boot env	8KB
 0x820		0256		FMAN Ucode	128KB
-0x920		0256		QE Firmware	128KB
+0x920		0256		QE Firmware	128KB(only T1024RDB)
 
 
-SPI Flash memory Map on T1024RDB
+64MB SPI Flash memory Map on T102xRDB
 ----------------------------------------------------
 Start		End		Definition	Size
 0x000000	0x0FFFFF	u-boot img	1MB
 0x100000	0x101FFF	u-boot env	8KB
 0x110000	0x12FFFF	FMAN Ucode	128KB
-0x130000	0x14FFFF	QE Firmware	128KB
+0x130000	0x14FFFF	QE Firmware	128KB(only T1024RDB)
+0x300000	0x3FFFFF	device tree	128KB
+0x400000	0x9FFFFF	Linux kernel    6MB
+0xa00000	0x3FFFFFF	rootfs		54MB
 
 
-For more details, please refer to T1024RDB Reference Manual and access
-website www.freescale.com and Freescale QorIQ SDK Infocenter document.
+For more details, please refer to T1024RDB Reference Manual
+and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
index a2a8f4c..adf9fd5 100644
--- a/board/freescale/t102xrdb/ddr.c
+++ b/board/freescale/t102xrdb/ddr.c
@@ -135,8 +135,83 @@
 	/* for DDR bus 32bit test on T1024 */
 	popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
 #endif
+
+#ifdef CONFIG_T1023RDB
+	popts->wrlvl_ctl_2 = 0x07070606;
+	popts->half_strength_driver_enable = 1;
+#endif
 }
 
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+/* 2GB discrete DDR4 MT40A512M8HX on T1023RDB */
+dimm_params_t ddr_raw_timing = {
+	.n_ranks = 1,
+	.rank_density = 0x80000000,
+	.capacity = 0x80000000,
+	.primary_sdram_width = 32,
+	.ec_sdram_width = 8,
+	.registered_dimm = 0,
+	.mirrored_dimm = 0,
+	.n_row_addr = 15,
+	.n_col_addr = 10,
+	.bank_addr_bits = 2,
+	.bank_group_bits = 2,
+	.edc_config = 0,
+	.burst_lengths_bitmask = 0x0c,
+	.tckmin_x_ps = 938,
+	.tckmax_ps = 1500,
+	.caslat_x = 0x000DFA00,
+	.taa_ps = 13500,
+	.trcd_ps = 13500,
+	.trp_ps = 13500,
+	.tras_ps = 33000,
+	.trc_ps = 46500,
+	.trfc1_ps = 260000,
+	.trfc2_ps = 160000,
+	.trfc4_ps = 110000,
+	.tfaw_ps = 25000,
+	.trrds_ps = 3700,
+	.trrdl_ps = 5300,
+	.tccdl_ps = 5355,
+	.refresh_rate_ps = 7800000,
+	.dq_mapping[0] = 0x0,
+	.dq_mapping[1] = 0x0,
+	.dq_mapping[2] = 0x0,
+	.dq_mapping[3] = 0x0,
+	.dq_mapping[4] = 0x0,
+	.dq_mapping[5] = 0x0,
+	.dq_mapping[6] = 0x0,
+	.dq_mapping[7] = 0x0,
+	.dq_mapping[8] = 0x0,
+	.dq_mapping[9] = 0x0,
+	.dq_mapping[10] = 0x0,
+	.dq_mapping[11] = 0x0,
+	.dq_mapping[12] = 0x0,
+	.dq_mapping[13] = 0x0,
+	.dq_mapping[14] = 0x0,
+	.dq_mapping[15] = 0x0,
+	.dq_mapping[16] = 0x0,
+	.dq_mapping[17] = 0x0,
+	.dq_mapping_ors = 1,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+		unsigned int controller_number,
+		unsigned int dimm_number)
+{
+	const char dimm_model[] = "Fixed DDR4 on board";
+
+	if (((controller_number == 0) && (dimm_number == 0)) ||
+	    ((controller_number == 1) && (dimm_number == 0))) {
+		memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+		memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+		memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+	}
+
+	return 0;
+}
+#endif
+
 #if defined(CONFIG_DEEP_SLEEP)
 void board_mem_sleep_setup(void)
 {
@@ -155,8 +230,9 @@
 	phys_size_t dram_size;
 
 #if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
+#ifndef CONFIG_SYS_DDR_RAW_TIMING
 	puts("Initializing....using SPD\n");
-
+#endif
 	dram_size = fsl_ddr_sdram();
 	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
 	dram_size *= 0x100000;
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index f611ff0..dd386bc 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -1,6 +1,8 @@
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
  * SPDX-License-Identifier:     GPL-2.0+
  */
 
@@ -56,6 +58,7 @@
 	fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
 
 	switch (srds_s1) {
+#ifdef CONFIG_T1024RDB
 	case 0x95:
 		/* set the on-board RGMII2  PHY */
 		fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
@@ -63,10 +66,17 @@
 		/* set 10G XFI with Aquantia AQR105 PHY */
 		fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
 		break;
+#endif
+	case 0x6a:
+	case 0x6b:
 	case 0x77:
 	case 0x135:
 		/* set the on-board 2.5G SGMII AQR105 PHY */
-		fm_info_set_phy_address(FM1_DTSEC3, SGMII_PHY1_ADDR);
+		fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
+#ifdef CONFIG_T1023RDB
+		/* set the on-board 1G SGMII RTL8211F PHY */
+		fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
+#endif
 		break;
 	default:
 		printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
@@ -81,6 +91,14 @@
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
 			fm_info_set_mdio(i, dev);
 			break;
+		case PHY_INTERFACE_MODE_SGMII:
+#if defined(CONFIG_T1023RDB)
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+#elif defined(CONFIG_T1024RDB)
+			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+#endif
+			fm_info_set_mdio(i, dev);
+			break;
 		case PHY_INTERFACE_MODE_SGMII_2500:
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
 			fm_info_set_mdio(i, dev);
@@ -110,13 +128,16 @@
 void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 			      enum fm_port port, int offset)
 {
-	if ((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) &&
-	    (port == FM1_DTSEC3)) {
+#if defined(CONFIG_T1024RDB)
+	if (((fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) ||
+	     (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII)) &&
+			(port == FM1_DTSEC3)) {
 		fdt_set_phy_handle(fdt, compat, addr, "sg_2500_aqr105_phy4");
 		fdt_setprop(fdt, offset, "phy-connection-type",
 			    "sgmii-2500", 10);
 		fdt_status_disabled_by_alias(fdt, "xg_aqr105_phy3");
 	}
+#endif
 }
 
 void fdt_fixup_board_enet(void *fdt)
diff --git a/board/freescale/t102xrdb/t1023_rcw.cfg b/board/freescale/t102xrdb/t1023_rcw.cfg
new file mode 100644
index 0000000..fa781d6
--- /dev/null
+++ b/board/freescale/t102xrdb/t1023_rcw.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header for T1023RDB
+aa55aa55 010e0100
+#SerDes Protocol: 0x77
+#Core/DDR: 1400Mhz/1600MT/s with single source clock
+0810000e 00000000 00000000 00000000
+3b800003 00000012 e8104000 21000000
+00000000 00000000 00000000 00020800
+00000130 04020200 00000000 00000006
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
index e196f12..f971976 100644
--- a/board/freescale/t102xrdb/t102xrdb.c
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -18,11 +18,25 @@
 #include <asm/fsl_liodn.h>
 #include <fm_eth.h>
 #include "t102xrdb.h"
+#ifdef CONFIG_T1024RDB
 #include "cpld.h"
+#endif
 #include "../common/sleep.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_T1023RDB
+enum {
+	GPIO1_SD_SEL    = 0x00020000, /* GPIO1_14, 0: EMMC, 1:SD/MMC */
+	GPIO1_EMMC_SEL,
+	GPIO1_VBANK0,
+	GPIO1_VBANK4    = 0x00008000, /* GPIO1_16/20/22,  100:vBank4 */
+	GPIO1_VBANK_MASK = 0x00008a00,
+	GPIO1_DIR_OUTPUT = 0x00028a00,
+	GPIO1_GET_VAL,
+};
+#endif
+
 int checkboard(void)
 {
 	struct cpu_type *cpu = gd->arch.cpu;
@@ -34,14 +48,17 @@
 	srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
 
 	printf("Board: %sRDB, ", cpu->name);
-	printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
+#ifdef CONFIG_T1024RDB
+	printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
 	       CPLD_READ(hw_ver), CPLD_READ(sw_ver));
+#endif
+	printf("boot from ");
 
 #ifdef CONFIG_SDCARD
 	puts("SD/MMC\n");
 #elif CONFIG_SPIFLASH
 	puts("SPI\n");
-#else
+#elif defined(CONFIG_T1024RDB)
 	u8 reg;
 
 	reg = CPLD_READ(flash_csr);
@@ -52,17 +69,25 @@
 		reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
 		printf("NOR vBank%d\n", reg);
 	}
+#elif defined(CONFIG_T1023RDB)
+#ifdef CONFIG_NAND
+	puts("NAND\n");
+#else
+	printf("NOR vBank%d\n", (t1023rdb_gpio_ctrl(GPIO1_GET_VAL) &
+	       GPIO1_VBANK4) >> 15 ? 4 : 0);
+#endif
 #endif
 
 	puts("SERDES Reference Clocks:\n");
 	if (srds_s1 == 0x95)
 		printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
 	else
-		printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[0]);
+		printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[0], freq[1]);
 
 	return 0;
 }
 
+#ifdef CONFIG_T1024RDB
 static void board_mux_lane(void)
 {
 	ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@@ -82,6 +107,7 @@
 	}
 	CPLD_WRITE(boot_override, CPLD_OVERRIDE_MUX_EN);
 }
+#endif
 
 int board_early_init_f(void)
 {
@@ -124,7 +150,9 @@
 #ifdef CONFIG_SYS_DPAA_QBMAN
 	setup_portals();
 #endif
+#ifdef CONFIG_T1024RDB
 	board_mux_lane();
+#endif
 
 	return 0;
 }
@@ -170,3 +198,62 @@
 
 	return 0;
 }
+
+
+#ifdef CONFIG_T1023RDB
+static u32 t1023rdb_gpio_ctrl(u32 ctrl_type)
+{
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 gpioval;
+
+	setbits_be32(&pgpio->gpdir, GPIO1_DIR_OUTPUT);
+	gpioval = in_be32(&pgpio->gpdat);
+
+	switch (ctrl_type) {
+	case GPIO1_SD_SEL:
+		gpioval |= GPIO1_SD_SEL;
+		break;
+	case GPIO1_EMMC_SEL:
+		gpioval &= ~GPIO1_SD_SEL;
+		break;
+	case GPIO1_VBANK0:
+		gpioval &= ~GPIO1_VBANK_MASK;
+		break;
+	case GPIO1_VBANK4:
+		gpioval &= ~GPIO1_VBANK_MASK;
+		gpioval |= GPIO1_VBANK4;
+		break;
+	case GPIO1_GET_VAL:
+		return gpioval;
+	default:
+		break;
+	}
+	out_be32(&pgpio->gpdat, gpioval);
+
+	return 0;
+}
+
+static int gpio_cmd(cmd_tbl_t *cmdtp, int flag, int argc,
+		    char * const argv[])
+{
+	if (argc < 2)
+		return CMD_RET_USAGE;
+	if (!strcmp(argv[1], "vbank0"))
+		t1023rdb_gpio_ctrl(GPIO1_VBANK0);
+	else if (!strcmp(argv[1], "vbank4"))
+		t1023rdb_gpio_ctrl(GPIO1_VBANK4);
+	else if (!strcmp(argv[1], "sd"))
+		t1023rdb_gpio_ctrl(GPIO1_SD_SEL);
+	else if (!strcmp(argv[1], "EMMC"))
+		t1023rdb_gpio_ctrl(GPIO1_EMMC_SEL);
+	else
+		return CMD_RET_USAGE;
+	return 0;
+}
+
+U_BOOT_CMD(
+	gpio, 2, 0, gpio_cmd,
+	"for vbank0/vbank4/SD/eMMC switch control in runtime",
+	"command (e.g. gpio vbank4)"
+);
+#endif
diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h
index 2f23579..3f5d85a 100644
--- a/board/freescale/t102xrdb/t102xrdb.h
+++ b/board/freescale/t102xrdb/t102xrdb.h
@@ -9,5 +9,7 @@
 
 void fdt_fixup_board_enet(void *blob);
 void pci_of_setup(void *blob, bd_t *bd);
-
+#ifdef CONFIG_T1023RDB
+static u32 t1023rdb_gpio_ctrl(u32 ctrl_type);
+#endif
 #endif