| From 02fb89a020d0bab2eac528f3d49379b535ebeda2 Mon Sep 17 00:00:00 2001 |
| From: Shayne Chen <shayne.chen@mediatek.com> |
| Date: Wed, 31 Jul 2024 10:42:08 +0800 |
| Subject: [PATCH 011/126] mtk: hostapd: sync with wireless-next.git |
| include/uapi/linux/nl80211.h |
| |
| This brings in nl80211 definitions as of 2024-07-11. |
| |
| Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> |
| --- |
| src/drivers/driver_nl80211_event.c | 1 + |
| src/drivers/nl80211_copy.h | 537 ++++++++++++++++++++--------- |
| 2 files changed, 370 insertions(+), 168 deletions(-) |
| |
| diff --git a/src/drivers/driver_nl80211_event.c b/src/drivers/driver_nl80211_event.c |
| index 768c72905..1787dbd99 100644 |
| --- a/src/drivers/driver_nl80211_event.c |
| +++ b/src/drivers/driver_nl80211_event.c |
| @@ -186,6 +186,7 @@ static const char * nl80211_command_to_string(enum nl80211_commands cmd) |
| C2S(NL80211_CMD_REMOVE_LINK_STA) |
| C2S(NL80211_CMD_SET_HW_TIMESTAMP) |
| C2S(NL80211_CMD_LINKS_REMOVED) |
| + C2S(NL80211_CMD_SET_TID_TO_LINK_MAPPING) |
| C2S(__NL80211_CMD_AFTER_LAST) |
| } |
| #undef C2S |
| diff --git a/src/drivers/nl80211_copy.h b/src/drivers/nl80211_copy.h |
| index dced2c49d..f97f5adc8 100644 |
| --- a/src/drivers/nl80211_copy.h |
| +++ b/src/drivers/nl80211_copy.h |
| @@ -11,7 +11,7 @@ |
| * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com> |
| * Copyright 2008 Colin McCabe <colin@cozybit.com> |
| * Copyright 2015-2017 Intel Deutschland GmbH |
| - * Copyright (C) 2018-2023 Intel Corporation |
| + * Copyright (C) 2018-2024 Intel Corporation |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| @@ -72,7 +72,7 @@ |
| * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS |
| * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows: |
| * - a setup station entry is added, not yet authorized, without any rate |
| - * or capability information, this just exists to avoid race conditions |
| + * or capability information; this just exists to avoid race conditions |
| * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid |
| * to add rate and capability information to the station and at the same |
| * time mark it authorized. |
| @@ -87,7 +87,7 @@ |
| * DOC: Frame transmission/registration support |
| * |
| * Frame transmission and registration support exists to allow userspace |
| - * management entities such as wpa_supplicant react to management frames |
| + * management entities such as wpa_supplicant to react to management frames |
| * that are not being handled by the kernel. This includes, for example, |
| * certain classes of action frames that cannot be handled in the kernel |
| * for various reasons. |
| @@ -113,7 +113,7 @@ |
| * |
| * Frame transmission allows userspace to send for example the required |
| * responses to action frames. It is subject to some sanity checking, |
| - * but many frames can be transmitted. When a frame was transmitted, its |
| + * but many frames can be transmitted. When a frame is transmitted, its |
| * status is indicated to the sending socket. |
| * |
| * For more technical details, see the corresponding command descriptions |
| @@ -123,7 +123,7 @@ |
| /** |
| * DOC: Virtual interface / concurrency capabilities |
| * |
| - * Some devices are able to operate with virtual MACs, they can have |
| + * Some devices are able to operate with virtual MACs; they can have |
| * more than one virtual interface. The capability handling for this |
| * is a bit complex though, as there may be a number of restrictions |
| * on the types of concurrency that are supported. |
| @@ -135,7 +135,7 @@ |
| * Once concurrency is desired, more attributes must be observed: |
| * To start with, since some interface types are purely managed in |
| * software, like the AP-VLAN type in mac80211 for example, there's |
| - * an additional list of these, they can be added at any time and |
| + * an additional list of these; they can be added at any time and |
| * are only restricted by some semantic restrictions (e.g. AP-VLAN |
| * cannot be added without a corresponding AP interface). This list |
| * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute. |
| @@ -164,7 +164,7 @@ |
| * Packet coalesce feature helps to reduce number of received interrupts |
| * to host by buffering these packets in firmware/hardware for some |
| * predefined time. Received interrupt will be generated when one of the |
| - * following events occur. |
| + * following events occurs. |
| * a) Expiration of hardware timer whose expiration time is set to maximum |
| * coalescing delay of matching coalesce rule. |
| * b) Coalescing buffer in hardware reaches its limit. |
| @@ -174,7 +174,7 @@ |
| * rule. |
| * a) Maximum coalescing delay |
| * b) List of packet patterns which needs to be matched |
| - * c) Condition for coalescence. pattern 'match' or 'no match' |
| + * c) Condition for coalescence: pattern 'match' or 'no match' |
| * Multiple such rules can be created. |
| */ |
| |
| @@ -213,7 +213,7 @@ |
| /** |
| * DOC: FILS shared key authentication offload |
| * |
| - * FILS shared key authentication offload can be advertized by drivers by |
| + * FILS shared key authentication offload can be advertised by drivers by |
| * setting @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD flag. The drivers that support |
| * FILS shared key authentication offload should be able to construct the |
| * authentication and association frames for FILS shared key authentication and |
| @@ -239,7 +239,7 @@ |
| * The PMKSA can be maintained in userspace persistently so that it can be used |
| * later after reboots or wifi turn off/on also. |
| * |
| - * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertized by a FILS |
| + * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertised by a FILS |
| * capable AP supporting PMK caching. It specifies the scope within which the |
| * PMKSAs are cached in an ESS. %NL80211_CMD_SET_PMKSA and |
| * %NL80211_CMD_DEL_PMKSA are enhanced to allow support for PMKSA caching based |
| @@ -290,12 +290,12 @@ |
| * If the configuration needs to be applied for specific peer then the MAC |
| * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the |
| * configuration will be applied for all the connected peers in the vif except |
| - * any peers that have peer specific configuration for the TID by default; if |
| - * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values |
| + * any peers that have peer-specific configuration for the TID by default; if |
| + * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer-specific values |
| * will be overwritten. |
| * |
| - * All this configuration is valid only for STA's current connection |
| - * i.e. the configuration will be reset to default when the STA connects back |
| + * All this configuration is valid only for STA's current connection, |
| + * i.e., the configuration will be reset to default when the STA connects back |
| * after disconnection/roaming, and this configuration will be cleared when |
| * the interface goes down. |
| */ |
| @@ -413,8 +413,8 @@ |
| * are like for %NL80211_CMD_SET_BEACON, and additionally parameters that |
| * do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL, |
| * %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID, |
| - * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE, |
| - * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, |
| + * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHER_SUITES_PAIRWISE, |
| + * %NL80211_ATTR_CIPHER_SUITE_GROUP, %NL80211_ATTR_WPA_VERSIONS, |
| * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, |
| * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT, |
| * %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS. |
| @@ -438,23 +438,19 @@ |
| * %NL80211_ATTR_REASON_CODE can optionally be used to specify which type |
| * of disconnection indication should be sent to the station |
| * (Deauthentication or Disassociation frame and reason code for that |
| - * frame). |
| + * frame). %NL80211_ATTR_MLO_LINK_ID can be used optionally to remove |
| + * stations connected and using at least that link as one of its links. |
| * |
| * @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to |
| - * destination %NL80211_ATTR_MAC on the interface identified by |
| - * %NL80211_ATTR_IFINDEX. |
| + * destination %NL80211_ATTR_MAC on the interface identified by |
| + * %NL80211_ATTR_IFINDEX. |
| * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to |
| - * destination %NL80211_ATTR_MAC on the interface identified by |
| - * %NL80211_ATTR_IFINDEX. |
| + * destination %NL80211_ATTR_MAC on the interface identified by |
| + * %NL80211_ATTR_IFINDEX. |
| * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by |
| * %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP. |
| * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by |
| * %NL80211_ATTR_MAC. |
| - * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the |
| - * interface identified by %NL80211_ATTR_IFINDEX. |
| - * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC |
| - * or, if no MAC address given, all mesh paths, on the interface identified |
| - * by %NL80211_ATTR_IFINDEX. |
| * @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by |
| * %NL80211_ATTR_IFINDEX. |
| * |
| @@ -475,15 +471,15 @@ |
| * after being queried by the kernel. CRDA replies by sending a regulatory |
| * domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our |
| * current alpha2 if it found a match. It also provides |
| - * NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each |
| - * regulatory rule is a nested set of attributes given by |
| - * %NL80211_ATTR_REG_RULE_FREQ_[START|END] and |
| - * %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by |
| - * %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and |
| - * %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP. |
| + * NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each |
| + * regulatory rule is a nested set of attributes given by |
| + * %NL80211_ATTR_REG_RULE_FREQ_[START|END] and |
| + * %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by |
| + * %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and |
| + * %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP. |
| * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain |
| - * to the specified ISO/IEC 3166-1 alpha2 country code. The core will |
| - * store this as a valid request and then query userspace for it. |
| + * to the specified ISO/IEC 3166-1 alpha2 country code. The core will |
| + * store this as a valid request and then query userspace for it. |
| * |
| * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the |
| * interface identified by %NL80211_ATTR_IFINDEX |
| @@ -521,7 +517,7 @@ |
| * %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is |
| * not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified, |
| * scheduled scan will run in an infinite loop with the specified interval. |
| - * These attributes are mutually exculsive, |
| + * These attributes are mutually exclusive, |
| * i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if |
| * NL80211_ATTR_SCHED_SCAN_PLANS is defined. |
| * If for some reason scheduled scan is aborted by the driver, all scan |
| @@ -552,7 +548,7 @@ |
| * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface |
| * is brought down while a scheduled scan was running. |
| * |
| - * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation |
| + * @NL80211_CMD_GET_SURVEY: get survey results, e.g. channel occupation |
| * or noise level |
| * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to |
| * NL80211_CMD_GET_SURVEY and on the "scan" multicast group) |
| @@ -563,40 +559,41 @@ |
| * using %NL80211_ATTR_SSID, %NL80211_ATTR_FILS_CACHE_ID, |
| * %NL80211_ATTR_PMKID, and %NL80211_ATTR_PMK in case of FILS |
| * authentication where %NL80211_ATTR_FILS_CACHE_ID is the identifier |
| - * advertized by a FILS capable AP identifying the scope of PMKSA in an |
| + * advertised by a FILS capable AP identifying the scope of PMKSA in an |
| * ESS. |
| * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC |
| * (for the BSSID) and %NL80211_ATTR_PMKID or using %NL80211_ATTR_SSID, |
| * %NL80211_ATTR_FILS_CACHE_ID, and %NL80211_ATTR_PMKID in case of FILS |
| - * authentication. |
| + * authentication. Additionally in case of SAE offload and OWE offloads |
| + * PMKSA entry can be deleted using %NL80211_ATTR_SSID. |
| * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries. |
| * |
| * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain |
| - * has been changed and provides details of the request information |
| - * that caused the change such as who initiated the regulatory request |
| - * (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx |
| - * (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if |
| - * the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or |
| - * %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain |
| - * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is |
| - * %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on |
| - * to (%NL80211_ATTR_REG_ALPHA2). |
| + * has been changed and provides details of the request information |
| + * that caused the change such as who initiated the regulatory request |
| + * (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx |
| + * (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if |
| + * the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or |
| + * %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain |
| + * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is |
| + * %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on |
| + * to (%NL80211_ATTR_REG_ALPHA2). |
| * @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon |
| - * has been found while world roaming thus enabling active scan or |
| - * any mode of operation that initiates TX (beacons) on a channel |
| - * where we would not have been able to do either before. As an example |
| - * if you are world roaming (regulatory domain set to world or if your |
| - * driver is using a custom world roaming regulatory domain) and while |
| - * doing a passive scan on the 5 GHz band you find an AP there (if not |
| - * on a DFS channel) you will now be able to actively scan for that AP |
| - * or use AP mode on your card on that same channel. Note that this will |
| - * never be used for channels 1-11 on the 2 GHz band as they are always |
| - * enabled world wide. This beacon hint is only sent if your device had |
| - * either disabled active scanning or beaconing on a channel. We send to |
| - * userspace the wiphy on which we removed a restriction from |
| - * (%NL80211_ATTR_WIPHY) and the channel on which this occurred |
| - * before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER) |
| - * the beacon hint was processed. |
| + * has been found while world roaming thus enabling active scan or |
| + * any mode of operation that initiates TX (beacons) on a channel |
| + * where we would not have been able to do either before. As an example |
| + * if you are world roaming (regulatory domain set to world or if your |
| + * driver is using a custom world roaming regulatory domain) and while |
| + * doing a passive scan on the 5 GHz band you find an AP there (if not |
| + * on a DFS channel) you will now be able to actively scan for that AP |
| + * or use AP mode on your card on that same channel. Note that this will |
| + * never be used for channels 1-11 on the 2 GHz band as they are always |
| + * enabled world wide. This beacon hint is only sent if your device had |
| + * either disabled active scanning or beaconing on a channel. We send to |
| + * userspace the wiphy on which we removed a restriction from |
| + * (%NL80211_ATTR_WIPHY) and the channel on which this occurred |
| + * before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER) |
| + * the beacon hint was processed. |
| * |
| * @NL80211_CMD_AUTHENTICATE: authentication request and notification. |
| * This command is used both as a command (request to authenticate) and |
| @@ -607,7 +604,7 @@ |
| * BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify |
| * the SSID (mainly for association, but is included in authentication |
| * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ + |
| - * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the |
| + * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequency of the |
| * channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the |
| * authentication type. %NL80211_ATTR_IE is used to define IEs |
| * (VendorSpecificInfo, but also including RSN IE and FT IEs) to be added |
| @@ -816,7 +813,7 @@ |
| * reached. |
| * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ |
| * and the attributes determining channel width) the given interface |
| - * (identifed by %NL80211_ATTR_IFINDEX) shall operate on. |
| + * (identified by %NL80211_ATTR_IFINDEX) shall operate on. |
| * In case multiple channels are supported by the device, the mechanism |
| * with which it switches channels is implementation-defined. |
| * When a monitor interface is given, it can only switch channel while |
| @@ -888,7 +885,7 @@ |
| * inform userspace of the new replay counter. |
| * |
| * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace |
| - * of PMKSA caching dandidates. |
| + * of PMKSA caching candidates. |
| * |
| * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup). |
| * In addition, this can be used as an event to request userspace to take |
| @@ -924,7 +921,7 @@ |
| * |
| * @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface |
| * by sending a null data frame to it and reporting when the frame is |
| - * acknowleged. This is used to allow timing out inactive clients. Uses |
| + * acknowledged. This is used to allow timing out inactive clients. Uses |
| * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a |
| * direct reply with an %NL80211_ATTR_COOKIE that is later used to match |
| * up the event with the request. The event includes the same data and |
| @@ -1118,7 +1115,7 @@ |
| * current configuration is not changed. If it is present but |
| * set to zero, the configuration is changed to don't-care |
| * (i.e. the device can decide what to do). |
| - * @NL80211_CMD_NAN_FUNC_MATCH: Notification sent when a match is reported. |
| + * @NL80211_CMD_NAN_MATCH: Notification sent when a match is reported. |
| * This will contain a %NL80211_ATTR_NAN_MATCH nested attribute and |
| * %NL80211_ATTR_COOKIE. |
| * |
| @@ -1135,11 +1132,15 @@ |
| * @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously |
| * configured PMK for the authenticator address identified by |
| * %NL80211_ATTR_MAC. |
| - * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates an 802.1X FT roam was |
| - * completed successfully. Drivers that support 4 way handshake offload |
| - * should send this event after indicating 802.1X FT assocation with |
| - * %NL80211_CMD_ROAM. If the 4 way handshake failed %NL80211_CMD_DISCONNECT |
| - * should be indicated instead. |
| + * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates port is authorized and |
| + * open for regular data traffic. For STA/P2P-client, this event is sent |
| + * with AP MAC address and for AP/P2P-GO, the event carries the STA/P2P- |
| + * client MAC address. |
| + * Drivers that support 4 way handshake offload should send this event for |
| + * STA/P2P-client after successful 4-way HS or after 802.1X FT following |
| + * NL80211_CMD_CONNECT or NL80211_CMD_ROAM. Drivers using AP/P2P-GO 4-way |
| + * handshake offload should send this event on successful completion of |
| + * 4-way handshake with the peer (STA/P2P-client). |
| * @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request |
| * and RX notification. This command is used both as a request to transmit |
| * a control port frame and as a notification that a control port frame |
| @@ -1323,6 +1324,11 @@ |
| * Multi-Link reconfiguration. %NL80211_ATTR_MLO_LINKS is used to provide |
| * information about the removed STA MLD setup links. |
| * |
| + * @NL80211_CMD_SET_TID_TO_LINK_MAPPING: Set the TID to Link Mapping for a |
| + * non-AP MLD station. The %NL80211_ATTR_MLO_TTLM_DLINK and |
| + * %NL80211_ATTR_MLO_TTLM_ULINK attributes are used to specify the |
| + * TID to Link mapping for downlink/uplink traffic. |
| + * |
| * @NL80211_CMD_MAX: highest used command number |
| * @__NL80211_CMD_AFTER_LAST: internal use |
| */ |
| @@ -1578,6 +1584,8 @@ enum nl80211_commands { |
| |
| NL80211_CMD_LINKS_REMOVED, |
| |
| + NL80211_CMD_SET_TID_TO_LINK_MAPPING, |
| + |
| /* add new commands above here */ |
| |
| /* used to define NL80211_CMD_MAX below */ |
| @@ -1702,21 +1710,21 @@ enum nl80211_commands { |
| * (see &enum nl80211_plink_action). |
| * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path. |
| * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path |
| - * info given for %NL80211_CMD_GET_MPATH, nested attribute described at |
| + * info given for %NL80211_CMD_GET_MPATH, nested attribute described at |
| * &enum nl80211_mpath_info. |
| * |
| * @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of |
| * &enum nl80211_mntr_flags. |
| * |
| * @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the |
| - * current regulatory domain should be set to or is already set to. |
| - * For example, 'CR', for Costa Rica. This attribute is used by the kernel |
| - * to query the CRDA to retrieve one regulatory domain. This attribute can |
| - * also be used by userspace to query the kernel for the currently set |
| - * regulatory domain. We chose an alpha2 as that is also used by the |
| - * IEEE-802.11 country information element to identify a country. |
| - * Users can also simply ask the wireless core to set regulatory domain |
| - * to a specific alpha2. |
| + * current regulatory domain should be set to or is already set to. |
| + * For example, 'CR', for Costa Rica. This attribute is used by the kernel |
| + * to query the CRDA to retrieve one regulatory domain. This attribute can |
| + * also be used by userspace to query the kernel for the currently set |
| + * regulatory domain. We chose an alpha2 as that is also used by the |
| + * IEEE-802.11 country information element to identify a country. |
| + * Users can also simply ask the wireless core to set regulatory domain |
| + * to a specific alpha2. |
| * @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory |
| * rules. |
| * |
| @@ -1759,9 +1767,9 @@ enum nl80211_commands { |
| * @NL80211_ATTR_BSS: scan result BSS |
| * |
| * @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain |
| - * currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_* |
| + * currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_* |
| * @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently |
| - * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*) |
| + * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*) |
| * |
| * @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies |
| * an array of command numbers (i.e. a mapping index to command number) |
| @@ -1780,15 +1788,15 @@ enum nl80211_commands { |
| * a u32 |
| * |
| * @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change |
| - * due to considerations from a beacon hint. This attribute reflects |
| - * the state of the channel _before_ the beacon hint processing. This |
| - * attributes consists of a nested attribute containing |
| - * NL80211_FREQUENCY_ATTR_* |
| + * due to considerations from a beacon hint. This attribute reflects |
| + * the state of the channel _before_ the beacon hint processing. This |
| + * attributes consists of a nested attribute containing |
| + * NL80211_FREQUENCY_ATTR_* |
| * @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change |
| - * due to considerations from a beacon hint. This attribute reflects |
| - * the state of the channel _after_ the beacon hint processing. This |
| - * attributes consists of a nested attribute containing |
| - * NL80211_FREQUENCY_ATTR_* |
| + * due to considerations from a beacon hint. This attribute reflects |
| + * the state of the channel _after_ the beacon hint processing. This |
| + * attributes consists of a nested attribute containing |
| + * NL80211_FREQUENCY_ATTR_* |
| * |
| * @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported |
| * cipher suites |
| @@ -1835,7 +1843,7 @@ enum nl80211_commands { |
| * using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is |
| * to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER |
| * flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth |
| - * frames are not forwared over the control port. |
| + * frames are not forwarded over the control port. |
| * |
| * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver. |
| * We recommend using nested, driver-specific attributes within this. |
| @@ -1849,12 +1857,6 @@ enum nl80211_commands { |
| * that protected APs should be used. This is also used with NEW_BEACON to |
| * indicate that the BSS is to use protection. |
| * |
| - * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON |
| - * to indicate which unicast key ciphers will be used with the connection |
| - * (an array of u32). |
| - * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to |
| - * indicate which group key cipher will be used with the connection (a |
| - * u32). |
| * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to |
| * indicate which WPA version(s) the AP we want to associate with is using |
| * (a u32 with flags from &enum nl80211_wpa_versions). |
| @@ -1885,6 +1887,7 @@ enum nl80211_commands { |
| * with %NL80211_KEY_* sub-attributes |
| * |
| * @NL80211_ATTR_PID: Process ID of a network namespace. |
| + * @NL80211_ATTR_NETNS_FD: File descriptor of a network namespace. |
| * |
| * @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for |
| * dumps. This number increases whenever the object list being |
| @@ -1939,6 +1942,7 @@ enum nl80211_commands { |
| * |
| * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was |
| * acknowledged by the recipient. |
| + * @NL80211_ATTR_ACK_SIGNAL: Station's ack signal strength (s32) |
| * |
| * @NL80211_ATTR_PS_STATE: powersave state, using &enum nl80211_ps_state values. |
| * |
| @@ -1972,10 +1976,10 @@ enum nl80211_commands { |
| * bit. Depending on which antennas are selected in the bitmap, 802.11n |
| * drivers can derive which chainmasks to use (if all antennas belonging to |
| * a particular chain are disabled this chain should be disabled) and if |
| - * a chain has diversity antennas wether diversity should be used or not. |
| + * a chain has diversity antennas whether diversity should be used or not. |
| * HT capabilities (STBC, TX Beamforming, Antenna selection) can be |
| * derived from the available chains after applying the antenna mask. |
| - * Non-802.11n drivers can derive wether to use diversity or not. |
| + * Non-802.11n drivers can derive whether to use diversity or not. |
| * Drivers may reject configurations or RX/TX mask combinations they cannot |
| * support by returning -EINVAL. |
| * |
| @@ -2048,6 +2052,10 @@ enum nl80211_commands { |
| * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported |
| * interface combinations. In each nested item, it contains attributes |
| * defined in &enum nl80211_if_combination_attrs. |
| + * If the wiphy uses multiple radios (@NL80211_ATTR_WIPHY_RADIOS is set), |
| + * this attribute contains the interface combinations of the first radio. |
| + * See @NL80211_ATTR_WIPHY_INTERFACE_COMBINATIONS for the global wiphy |
| + * combinations for the sum of all radios. |
| * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like |
| * %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that |
| * are managed in software: interfaces of these types aren't subject to |
| @@ -2136,6 +2144,9 @@ enum nl80211_commands { |
| * @NL80211_ATTR_DISABLE_HE: Force HE capable interfaces to disable |
| * this feature during association. This is a flag attribute. |
| * Currently only supported in mac80211 drivers. |
| + * @NL80211_ATTR_DISABLE_EHT: Force EHT capable interfaces to disable |
| + * this feature during association. This is a flag attribute. |
| + * Currently only supported in mac80211 drivers. |
| * @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the |
| * ATTR_HT_CAPABILITY to which attention should be paid. |
| * Currently, only mac80211 NICs support this feature. |
| @@ -2145,6 +2156,12 @@ enum nl80211_commands { |
| * All values are treated as suggestions and may be ignored |
| * by the driver as required. The actual values may be seen in |
| * the station debugfs ht_caps file. |
| + * @NL80211_ATTR_VHT_CAPABILITY_MASK: Specify which bits of the |
| + * ATTR_VHT_CAPABILITY to which attention should be paid. |
| + * Currently, only mac80211 NICs support this feature. |
| + * All values are treated as suggestions and may be ignored |
| + * by the driver as required. The actual values may be seen in |
| + * the station debugfs vht_caps file. |
| * |
| * @NL80211_ATTR_DFS_REGION: region for regulatory rules which this country |
| * abides to when initiating radiation on DFS channels. A country maps |
| @@ -2403,7 +2420,7 @@ enum nl80211_commands { |
| * scheduled scan is started. Or the delay before a WoWLAN |
| * net-detect scan is started, counting from the moment the |
| * system is suspended. This value is a u32, in seconds. |
| - |
| + * |
| * @NL80211_ATTR_REG_INDOOR: flag attribute, if set indicates that the device |
| * is operating in an indoor environment. |
| * |
| @@ -2545,7 +2562,7 @@ enum nl80211_commands { |
| * from successful FILS authentication and is used with |
| * %NL80211_CMD_CONNECT. |
| * |
| - * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP |
| + * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertised by a FILS AP |
| * identifying the scope of PMKSAs. This is used with |
| * @NL80211_CMD_SET_PMKSA and @NL80211_CMD_DEL_PMKSA. |
| * |
| @@ -2826,6 +2843,31 @@ enum nl80211_commands { |
| * @NL80211_ATTR_MLO_LINK_DISABLED: Flag attribute indicating that the link is |
| * disabled. |
| * |
| + * @NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA: Include BSS usage data, i.e. |
| + * include BSSes that can only be used in restricted scenarios and/or |
| + * cannot be used at all. |
| + * |
| + * @NL80211_ATTR_MLO_TTLM_DLINK: Binary attribute specifying the downlink TID to |
| + * link mapping. The length is 8 * sizeof(u16). For each TID the link |
| + * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element) |
| + * in Draft P802.11be_D4.0. |
| + * @NL80211_ATTR_MLO_TTLM_ULINK: Binary attribute specifying the uplink TID to |
| + * link mapping. The length is 8 * sizeof(u16). For each TID the link |
| + * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element) |
| + * in Draft P802.11be_D4.0. |
| + * |
| + * @NL80211_ATTR_ASSOC_SPP_AMSDU: flag attribute used with |
| + * %NL80211_CMD_ASSOCIATE indicating the SPP A-MSDUs |
| + * are used on this connection |
| + * |
| + * @NL80211_ATTR_WIPHY_RADIOS: Nested attribute describing physical radios |
| + * belonging to this wiphy. See &enum nl80211_wiphy_radio_attrs. |
| + * |
| + * @NL80211_ATTR_WIPHY_INTERFACE_COMBINATIONS: Nested attribute listing the |
| + * supported interface combinations for all radios combined. In each |
| + * nested item, it contains attributes defined in |
| + * &enum nl80211_if_combination_attrs. |
| + * |
| * @NUM_NL80211_ATTR: total number of nl80211_attrs available |
| * @NL80211_ATTR_MAX: highest attribute number currently defined |
| * @__NL80211_ATTR_AFTER_LAST: internal use |
| @@ -3364,6 +3406,16 @@ enum nl80211_attrs { |
| |
| NL80211_ATTR_MLO_LINK_DISABLED, |
| |
| + NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA, |
| + |
| + NL80211_ATTR_MLO_TTLM_DLINK, |
| + NL80211_ATTR_MLO_TTLM_ULINK, |
| + |
| + NL80211_ATTR_ASSOC_SPP_AMSDU, |
| + |
| + NL80211_ATTR_WIPHY_RADIOS, |
| + NL80211_ATTR_WIPHY_INTERFACE_COMBINATIONS, |
| + |
| /* add attributes here, update the policy in nl80211.c */ |
| |
| __NL80211_ATTR_AFTER_LAST, |
| @@ -3504,6 +3556,7 @@ enum nl80211_iftype { |
| * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers |
| * that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a |
| * previously added station into associated state |
| + * @NL80211_STA_FLAG_SPP_AMSDU: station supports SPP A-MSDUs |
| * @NL80211_STA_FLAG_MAX: highest station flag number currently defined |
| * @__NL80211_STA_FLAG_AFTER_LAST: internal use |
| */ |
| @@ -3516,6 +3569,7 @@ enum nl80211_sta_flags { |
| NL80211_STA_FLAG_AUTHENTICATED, |
| NL80211_STA_FLAG_TDLS_PEER, |
| NL80211_STA_FLAG_ASSOCIATED, |
| + NL80211_STA_FLAG_SPP_AMSDU, |
| |
| /* keep last */ |
| __NL80211_STA_FLAG_AFTER_LAST, |
| @@ -3526,7 +3580,7 @@ enum nl80211_sta_flags { |
| * enum nl80211_sta_p2p_ps_status - station support of P2P PS |
| * |
| * @NL80211_P2P_PS_UNSUPPORTED: station doesn't support P2P PS mechanism |
| - * @@NL80211_P2P_PS_SUPPORTED: station supports P2P PS mechanism |
| + * @NL80211_P2P_PS_SUPPORTED: station supports P2P PS mechanism |
| * @NUM_NL80211_P2P_PS_STATUS: number of values |
| */ |
| enum nl80211_sta_p2p_ps_status { |
| @@ -3564,9 +3618,9 @@ enum nl80211_he_gi { |
| |
| /** |
| * enum nl80211_he_ltf - HE long training field |
| - * @NL80211_RATE_INFO_HE_1xLTF: 3.2 usec |
| - * @NL80211_RATE_INFO_HE_2xLTF: 6.4 usec |
| - * @NL80211_RATE_INFO_HE_4xLTF: 12.8 usec |
| + * @NL80211_RATE_INFO_HE_1XLTF: 3.2 usec |
| + * @NL80211_RATE_INFO_HE_2XLTF: 6.4 usec |
| + * @NL80211_RATE_INFO_HE_4XLTF: 12.8 usec |
| */ |
| enum nl80211_he_ltf { |
| NL80211_RATE_INFO_HE_1XLTF, |
| @@ -3681,7 +3735,7 @@ enum nl80211_eht_ru_alloc { |
| * @NL80211_RATE_INFO_HE_GI: HE guard interval identifier |
| * (u8, see &enum nl80211_he_gi) |
| * @NL80211_RATE_INFO_HE_DCM: HE DCM value (u8, 0/1) |
| - * @NL80211_RATE_INFO_RU_ALLOC: HE RU allocation, if not present then |
| + * @NL80211_RATE_INFO_HE_RU_ALLOC: HE RU allocation, if not present then |
| * non-OFDMA was used (u8, see &enum nl80211_he_ru_alloc) |
| * @NL80211_RATE_INFO_320_MHZ_WIDTH: 320 MHz bitrate |
| * @NL80211_RATE_INFO_EHT_MCS: EHT MCS index (u8, 0-15) |
| @@ -3784,7 +3838,7 @@ enum nl80211_sta_bss_param { |
| * (u64, to this station) |
| * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm) |
| * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute |
| - * containing info as possible, see &enum nl80211_rate_info |
| + * containing info as possible, see &enum nl80211_rate_info |
| * @NL80211_STA_INFO_RX_PACKETS: total received packet (MSDUs and MMPDUs) |
| * (u32, from this station) |
| * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (MSDUs and MMPDUs) |
| @@ -3813,8 +3867,8 @@ enum nl80211_sta_bss_param { |
| * Contains a nested array of signal strength attributes (u8, dBm) |
| * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average |
| * Same format as NL80211_STA_INFO_CHAIN_SIGNAL. |
| - * @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the |
| - * 802.11 header (u32, kbps) |
| + * @NL80211_STA_INFO_EXPECTED_THROUGHPUT: expected throughput considering also |
| + * the 802.11 header (u32, kbps) |
| * @NL80211_STA_INFO_RX_DROP_MISC: RX packets dropped for unspecified reasons |
| * (u64) |
| * @NL80211_STA_INFO_BEACON_RX: number of beacons received from this peer (u64) |
| @@ -4000,7 +4054,7 @@ enum nl80211_mpath_flags { |
| * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path |
| * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now |
| * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in |
| - * &enum nl80211_mpath_flags; |
| + * &enum nl80211_mpath_flags; |
| * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec |
| * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries |
| * @NL80211_MPATH_INFO_HOP_COUNT: hop count to destination |
| @@ -4140,7 +4194,7 @@ enum nl80211_band_attr { |
| * @NL80211_WMMR_CW_MAX: Maximum contention window slot. |
| * @NL80211_WMMR_AIFSN: Arbitration Inter Frame Space. |
| * @NL80211_WMMR_TXOP: Maximum allowed tx operation time. |
| - * @nl80211_WMMR_MAX: highest possible wmm rule. |
| + * @NL80211_WMMR_MAX: highest possible wmm rule. |
| * @__NL80211_WMMR_LAST: Internal use. |
| */ |
| enum nl80211_wmm_rule { |
| @@ -4162,15 +4216,16 @@ enum nl80211_wmm_rule { |
| * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current |
| * regulatory domain. |
| * @NL80211_FREQUENCY_ATTR_NO_IR: no mechanisms that initiate radiation |
| - * are permitted on this channel, this includes sending probe |
| - * requests, or modes of operation that require beaconing. |
| + * are permitted on this channel, this includes sending probe |
| + * requests, or modes of operation that require beaconing. |
| + * @__NL80211_FREQUENCY_ATTR_NO_IBSS: obsolete, same as _NO_IR |
| * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory |
| * on this channel in current regulatory domain. |
| * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm |
| * (100 * dBm). |
| * @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS |
| * (enum nl80211_dfs_state) |
| - * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long |
| + * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in milliseconds for how long |
| * this channel is in this DFS state. |
| * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this |
| * channel as the control channel |
| @@ -4226,6 +4281,19 @@ enum nl80211_wmm_rule { |
| * in current regulatory domain. |
| * @NL80211_FREQUENCY_ATTR_PSD: Power spectral density (in dBm) that |
| * is allowed on this channel in current regulatory domain. |
| + * @NL80211_FREQUENCY_ATTR_DFS_CONCURRENT: Operation on this channel is |
| + * allowed for peer-to-peer or adhoc communication under the control |
| + * of a DFS master which operates on the same channel (FCC-594280 D01 |
| + * Section B.3). Should be used together with %NL80211_RRF_DFS only. |
| + * @NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP |
| + * not allowed using this channel |
| + * @NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP |
| + * not allowed using this channel |
| + * @NL80211_FREQUENCY_ATTR_CAN_MONITOR: This channel can be used in monitor |
| + * mode despite other (regulatory) restrictions, even if the channel is |
| + * otherwise completely disabled. |
| + * @NL80211_FREQUENCY_ATTR_ALLOW_6GHZ_VLP_AP: This channel can be used for a |
| + * very low power (VLP) AP, despite being NO_IR. |
| * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number |
| * currently defined |
| * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use |
| @@ -4265,6 +4333,11 @@ enum nl80211_frequency_attr { |
| NL80211_FREQUENCY_ATTR_NO_320MHZ, |
| NL80211_FREQUENCY_ATTR_NO_EHT, |
| NL80211_FREQUENCY_ATTR_PSD, |
| + NL80211_FREQUENCY_ATTR_DFS_CONCURRENT, |
| + NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT, |
| + NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT, |
| + NL80211_FREQUENCY_ATTR_CAN_MONITOR, |
| + NL80211_FREQUENCY_ATTR_ALLOW_6GHZ_VLP_AP, |
| |
| /* keep last */ |
| __NL80211_FREQUENCY_ATTR_AFTER_LAST, |
| @@ -4277,6 +4350,10 @@ enum nl80211_frequency_attr { |
| #define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR |
| #define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \ |
| NL80211_FREQUENCY_ATTR_IR_CONCURRENT |
| +#define NL80211_FREQUENCY_ATTR_NO_UHB_VLP_CLIENT \ |
| + NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT |
| +#define NL80211_FREQUENCY_ATTR_NO_UHB_AFC_CLIENT \ |
| + NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT |
| |
| /** |
| * enum nl80211_bitrate_attr - bitrate attributes |
| @@ -4299,16 +4376,16 @@ enum nl80211_bitrate_attr { |
| }; |
| |
| /** |
| - * enum nl80211_initiator - Indicates the initiator of a reg domain request |
| + * enum nl80211_reg_initiator - Indicates the initiator of a reg domain request |
| * @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world |
| - * regulatory domain. |
| + * regulatory domain. |
| * @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the |
| - * regulatory domain. |
| + * regulatory domain. |
| * @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the |
| - * wireless core it thinks its knows the regulatory domain we should be in. |
| + * wireless core it thinks its knows the regulatory domain we should be in. |
| * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an |
| - * 802.11 country information element with regulatory information it |
| - * thinks we should consider. cfg80211 only processes the country |
| + * 802.11 country information element with regulatory information it |
| + * thinks we should consider. cfg80211 only processes the country |
| * code from the IE, and relies on the regulatory domain information |
| * structure passed by userspace (CRDA) from our wireless-regdb. |
| * If a channel is enabled but the country code indicates it should |
| @@ -4327,11 +4404,11 @@ enum nl80211_reg_initiator { |
| * to a specific country. When this is set you can count on the |
| * ISO / IEC 3166 alpha2 country code being valid. |
| * @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory |
| - * domain. |
| + * domain. |
| * @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom |
| - * driver specific world regulatory domain. These do not apply system-wide |
| - * and are only applicable to the individual devices which have requested |
| - * them to be applied. |
| + * driver specific world regulatory domain. These do not apply system-wide |
| + * and are only applicable to the individual devices which have requested |
| + * them to be applied. |
| * @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product |
| * of an intersection between two regulatory domains -- the previously |
| * set regulatory domain on the system and the last accepted regulatory |
| @@ -4348,21 +4425,21 @@ enum nl80211_reg_type { |
| * enum nl80211_reg_rule_attr - regulatory rule attributes |
| * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved |
| * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional |
| - * considerations for a given frequency range. These are the |
| - * &enum nl80211_reg_rule_flags. |
| + * considerations for a given frequency range. These are the |
| + * &enum nl80211_reg_rule_flags. |
| * @NL80211_ATTR_FREQ_RANGE_START: starting frequencry for the regulatory |
| - * rule in KHz. This is not a center of frequency but an actual regulatory |
| - * band edge. |
| + * rule in KHz. This is not a center of frequency but an actual regulatory |
| + * band edge. |
| * @NL80211_ATTR_FREQ_RANGE_END: ending frequency for the regulatory rule |
| - * in KHz. This is not a center a frequency but an actual regulatory |
| - * band edge. |
| + * in KHz. This is not a center a frequency but an actual regulatory |
| + * band edge. |
| * @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this |
| * frequency range, in KHz. |
| * @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain |
| - * for a given frequency range. The value is in mBi (100 * dBi). |
| - * If you don't have one then don't send this. |
| + * for a given frequency range. The value is in mBi (100 * dBi). |
| + * If you don't have one then don't send this. |
| * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for |
| - * a given frequency range. The value is in mBm (100 * dBm). |
| + * a given frequency range. The value is in mBm (100 * dBm). |
| * @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds. |
| * If not present or 0 default CAC time will be used. |
| * @NL80211_ATTR_POWER_RULE_PSD: power spectral density (in dBm). |
| @@ -4414,14 +4491,7 @@ enum nl80211_reg_rule_attr { |
| * value as specified by &struct nl80211_bss_select_rssi_adjust. |
| * @NL80211_SCHED_SCAN_MATCH_ATTR_BSSID: BSSID to be used for matching |
| * (this cannot be used together with SSID). |
| - * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the |
| - * band specific minimum rssi thresholds for the bands defined in |
| - * enum nl80211_band. The minimum rssi threshold value(s32) specific to a |
| - * band shall be encapsulated in attribute with type value equals to one |
| - * of the NL80211_BAND_* defined in enum nl80211_band. For example, the |
| - * minimum rssi threshold value for 2.4GHZ band shall be encapsulated |
| - * within an attribute of type NL80211_BAND_2GHZ. And one or more of such |
| - * attributes will be nested within this attribute. |
| + * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Obsolete |
| * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter |
| * attribute number currently defined |
| * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use |
| @@ -4434,7 +4504,7 @@ enum nl80211_sched_scan_match_attr { |
| NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI, |
| NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST, |
| NL80211_SCHED_SCAN_MATCH_ATTR_BSSID, |
| - NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI, |
| + NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI, /* obsolete */ |
| |
| /* keep last */ |
| __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST, |
| @@ -4456,8 +4526,9 @@ enum nl80211_sched_scan_match_attr { |
| * @NL80211_RRF_PTP_ONLY: this is only for Point To Point links |
| * @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links |
| * @NL80211_RRF_NO_IR: no mechanisms that initiate radiation are allowed, |
| - * this includes probe requests or modes of operation that require |
| - * beaconing. |
| + * this includes probe requests or modes of operation that require |
| + * beaconing. |
| + * @__NL80211_RRF_NO_IBSS: obsolete, same as NO_IR |
| * @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated |
| * base on contiguous rules and wider channels will be allowed to cross |
| * multiple contiguous/overlapping frequency ranges. |
| @@ -4470,6 +4541,14 @@ enum nl80211_sched_scan_match_attr { |
| * @NL80211_RRF_NO_320MHZ: 320MHz operation not allowed |
| * @NL80211_RRF_NO_EHT: EHT operation not allowed |
| * @NL80211_RRF_PSD: Ruleset has power spectral density value |
| + * @NL80211_RRF_DFS_CONCURRENT: Operation on this channel is allowed for |
| + * peer-to-peer or adhoc communication under the control of a DFS master |
| + * which operates on the same channel (FCC-594280 D01 Section B.3). |
| + * Should be used together with %NL80211_RRF_DFS only. |
| + * @NL80211_RRF_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP not allowed |
| + * @NL80211_RRF_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP not allowed |
| + * @NL80211_RRF_ALLOW_6GHZ_VLP_AP: Very low power (VLP) AP can be permitted |
| + * despite NO_IR configuration. |
| */ |
| enum nl80211_reg_rule_flags { |
| NL80211_RRF_NO_OFDM = 1<<0, |
| @@ -4491,6 +4570,10 @@ enum nl80211_reg_rule_flags { |
| NL80211_RRF_NO_320MHZ = 1<<18, |
| NL80211_RRF_NO_EHT = 1<<19, |
| NL80211_RRF_PSD = 1<<20, |
| + NL80211_RRF_DFS_CONCURRENT = 1<<21, |
| + NL80211_RRF_NO_6GHZ_VLP_CLIENT = 1<<22, |
| + NL80211_RRF_NO_6GHZ_AFC_CLIENT = 1<<23, |
| + NL80211_RRF_ALLOW_6GHZ_VLP_AP = 1<<24, |
| }; |
| |
| #define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR |
| @@ -4499,6 +4582,8 @@ enum nl80211_reg_rule_flags { |
| #define NL80211_RRF_NO_HT40 (NL80211_RRF_NO_HT40MINUS |\ |
| NL80211_RRF_NO_HT40PLUS) |
| #define NL80211_RRF_GO_CONCURRENT NL80211_RRF_IR_CONCURRENT |
| +#define NL80211_RRF_NO_UHB_VLP_CLIENT NL80211_RRF_NO_6GHZ_VLP_CLIENT |
| +#define NL80211_RRF_NO_UHB_AFC_CLIENT NL80211_RRF_NO_6GHZ_AFC_CLIENT |
| |
| /* For backport compatibility with older userspace */ |
| #define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS) |
| @@ -4645,8 +4730,8 @@ enum nl80211_mntr_flags { |
| * alternate between Active and Doze states, but may not wake up |
| * for neighbor's beacons. |
| * |
| - * @__NL80211_MESH_POWER_AFTER_LAST - internal use |
| - * @NL80211_MESH_POWER_MAX - highest possible power save level |
| + * @__NL80211_MESH_POWER_AFTER_LAST: internal use |
| + * @NL80211_MESH_POWER_MAX: highest possible power save level |
| */ |
| |
| enum nl80211_mesh_power_mode { |
| @@ -5027,6 +5112,36 @@ enum nl80211_bss_scan_width { |
| NL80211_BSS_CHAN_WIDTH_2, |
| }; |
| |
| +/** |
| + * enum nl80211_bss_use_for - bitmap indicating possible BSS use |
| + * @NL80211_BSS_USE_FOR_NORMAL: Use this BSS for normal "connection", |
| + * including IBSS/MBSS depending on the type. |
| + * @NL80211_BSS_USE_FOR_MLD_LINK: This BSS can be used as a link in an |
| + * MLO connection. Note that for an MLO connection, all links including |
| + * the assoc link must have this flag set, and the assoc link must |
| + * additionally have %NL80211_BSS_USE_FOR_NORMAL set. |
| + */ |
| +enum nl80211_bss_use_for { |
| + NL80211_BSS_USE_FOR_NORMAL = 1 << 0, |
| + NL80211_BSS_USE_FOR_MLD_LINK = 1 << 1, |
| +}; |
| + |
| +/** |
| + * enum nl80211_bss_cannot_use_reasons - reason(s) connection to a |
| + * BSS isn't possible |
| + * @NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY: NSTR nonprimary links aren't |
| + * supported by the device, and this BSS entry represents one. |
| + * @NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH: STA is not supporting |
| + * the AP power type (SP, VLP, AP) that the AP uses. |
| + */ |
| +enum nl80211_bss_cannot_use_reasons { |
| + NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY = 1 << 0, |
| + NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH = 1 << 1, |
| +}; |
| + |
| +#define NL80211_BSS_CANNOT_USE_UHB_PWR_MISMATCH \ |
| + NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH |
| + |
| /** |
| * enum nl80211_bss - netlink attributes for a BSS |
| * |
| @@ -5079,6 +5194,14 @@ enum nl80211_bss_scan_width { |
| * @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz |
| * @NL80211_BSS_MLO_LINK_ID: MLO link ID of the BSS (u8). |
| * @NL80211_BSS_MLD_ADDR: MLD address of this BSS if connected to it. |
| + * @NL80211_BSS_USE_FOR: u32 bitmap attribute indicating what the BSS can be |
| + * used for, see &enum nl80211_bss_use_for. |
| + * @NL80211_BSS_CANNOT_USE_REASONS: Indicates the reason that this BSS cannot |
| + * be used for all or some of the possible uses by the device reporting it, |
| + * even though its presence was detected. |
| + * This is a u64 attribute containing a bitmap of values from |
| + * &enum nl80211_cannot_use_reasons, note that the attribute may be missing |
| + * if no reasons are specified. |
| * @__NL80211_BSS_AFTER_LAST: internal |
| * @NL80211_BSS_MAX: highest BSS attribute |
| */ |
| @@ -5106,6 +5229,8 @@ enum nl80211_bss { |
| NL80211_BSS_FREQUENCY_OFFSET, |
| NL80211_BSS_MLO_LINK_ID, |
| NL80211_BSS_MLD_ADDR, |
| + NL80211_BSS_USE_FOR, |
| + NL80211_BSS_CANNOT_USE_REASONS, |
| |
| /* keep last */ |
| __NL80211_BSS_AFTER_LAST, |
| @@ -5454,7 +5579,7 @@ enum nl80211_tx_rate_setting { |
| * (%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE). |
| * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but |
| * per peer instead. |
| - * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates |
| + * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribute, if set indicates |
| * that the new configuration overrides all previous peer |
| * configurations, otherwise previous peer specific configurations |
| * should be left untouched. |
| @@ -5626,7 +5751,7 @@ struct nl80211_pattern_support { |
| * "TCP connection wakeup" for more details. This is a nested attribute |
| * containing the exact information for establishing and keeping alive |
| * the TCP connection. |
| - * @NL80211_WOWLAN_TRIG_TCP_WAKEUP_MATCH: For wakeup reporting only, the |
| + * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_MATCH: For wakeup reporting only, the |
| * wakeup packet was received on the TCP connection |
| * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST: For wakeup reporting only, the |
| * TCP connection was lost or failed to be established |
| @@ -5655,6 +5780,8 @@ struct nl80211_pattern_support { |
| * %NL80211_ATTR_SCAN_FREQUENCIES contains more than one |
| * frequency, it means that the match occurred in more than one |
| * channel. |
| + * @NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC: For wakeup reporting only. |
| + * Wake up happened due to unprotected deauth or disassoc frame in MFP. |
| * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers |
| * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number |
| * |
| @@ -5682,6 +5809,7 @@ enum nl80211_wowlan_triggers { |
| NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS, |
| NL80211_WOWLAN_TRIG_NET_DETECT, |
| NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS, |
| + NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC, |
| |
| /* keep last */ |
| NUM_NL80211_WOWLAN_TRIG, |
| @@ -5837,7 +5965,7 @@ enum nl80211_attr_coalesce_rule { |
| |
| /** |
| * enum nl80211_coalesce_condition - coalesce rule conditions |
| - * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns |
| + * @NL80211_COALESCE_CONDITION_MATCH: coalesce Rx packets when patterns |
| * in a rule are matched. |
| * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns |
| * in a rule are not matched. |
| @@ -5936,7 +6064,7 @@ enum nl80211_if_combination_attrs { |
| * enum nl80211_plink_state - state of a mesh peer link finite state machine |
| * |
| * @NL80211_PLINK_LISTEN: initial state, considered the implicit |
| - * state of non existent mesh peer links |
| + * state of non-existent mesh peer links |
| * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to |
| * this mesh peer |
| * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received |
| @@ -5972,7 +6100,7 @@ enum nl80211_plink_state { |
| * @NL80211_PLINK_ACTION_BLOCK: block traffic from this mesh peer |
| * @NUM_NL80211_PLINK_ACTIONS: number of possible actions |
| */ |
| -enum plink_actions { |
| +enum nl80211_plink_action { |
| NL80211_PLINK_ACTION_NO_ACTION, |
| NL80211_PLINK_ACTION_OPEN, |
| NL80211_PLINK_ACTION_BLOCK, |
| @@ -6229,7 +6357,7 @@ enum nl80211_feature_flags { |
| * request to use RRM (see %NL80211_ATTR_USE_RRM) with |
| * %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set |
| * the ASSOC_REQ_USE_RRM flag in the association request even if |
| - * NL80211_FEATURE_QUIET is not advertized. |
| + * NL80211_FEATURE_QUIET is not advertised. |
| * @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air |
| * sniffer which means that it can be configured to hear packets from |
| * certain groups which can be configured by the |
| @@ -6241,13 +6369,15 @@ enum nl80211_feature_flags { |
| * the BSS that the interface that requested the scan is connected to |
| * (if available). |
| * @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the |
| - * time the last beacon/probe was received. The time is the TSF of the |
| - * BSS that the interface that requested the scan is connected to |
| - * (if available). |
| + * time the last beacon/probe was received. For a non-MLO connection, the |
| + * time is the TSF of the BSS that the interface that requested the scan is |
| + * connected to (if available). For an MLO connection, the time is the TSF |
| + * of the BSS corresponding with link ID specified in the scan request (if |
| + * specified). |
| * @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of |
| * channel dwell time. |
| * @NL80211_EXT_FEATURE_BEACON_RATE_LEGACY: Driver supports beacon rate |
| - * configuration (AP/mesh), supporting a legacy (non HT/VHT) rate. |
| + * configuration (AP/mesh), supporting a legacy (non-HT/VHT) rate. |
| * @NL80211_EXT_FEATURE_BEACON_RATE_HT: Driver supports beacon rate |
| * configuration (AP/mesh) with HT rates. |
| * @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate |
| @@ -6297,6 +6427,7 @@ enum nl80211_feature_flags { |
| * receiving control port frames over nl80211 instead of the netdevice. |
| * @NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT: This driver/device supports |
| * (average) ACK signal strength reporting. |
| + * @NL80211_EXT_FEATURE_DATA_ACK_SIGNAL_SUPPORT: Backward-compatible ID |
| * @NL80211_EXT_FEATURE_TXQS: Driver supports FQ-CoDel-enabled intermediate |
| * TXQs. |
| * @NL80211_EXT_FEATURE_SCAN_RANDOM_SN: Driver/device supports randomizing the |
| @@ -6321,8 +6452,7 @@ enum nl80211_feature_flags { |
| * @NL80211_EXT_FEATURE_AP_PMKSA_CACHING: Driver/device supports PMKSA caching |
| * (set/del PMKSA operations) in AP mode. |
| * |
| - * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Driver supports |
| - * filtering of sched scan results using band specific RSSI thresholds. |
| + * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Obsolete |
| * |
| * @NL80211_EXT_FEATURE_STA_TX_PWR: This driver supports controlling tx power |
| * to a station. |
| @@ -6426,6 +6556,16 @@ enum nl80211_feature_flags { |
| * @NL80211_EXT_FEATURE_OWE_OFFLOAD_AP: Driver/Device wants to do OWE DH IE |
| * handling in AP mode. |
| * |
| + * @NL80211_EXT_FEATURE_DFS_CONCURRENT: The device supports peer-to-peer or |
| + * ad hoc operation on DFS channels under the control of a concurrent |
| + * DFS master on the same channel as described in FCC-594280 D01 |
| + * (Section B.3). This, for example, allows P2P GO and P2P clients to |
| + * operate on DFS channels as long as there's a concurrent BSS connection. |
| + * |
| + * @NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT: The driver has support for SPP |
| + * (signaling and payload protected) A-MSDUs and this shall be advertised |
| + * in the RSNXE. |
| + * |
| * @NUM_NL80211_EXT_FEATURES: number of extended features. |
| * @MAX_NL80211_EXT_FEATURES: highest extended feature index. |
| */ |
| @@ -6467,7 +6607,7 @@ enum nl80211_ext_feature_index { |
| NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER, |
| NL80211_EXT_FEATURE_AIRTIME_FAIRNESS, |
| NL80211_EXT_FEATURE_AP_PMKSA_CACHING, |
| - NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD, |
| + NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD, /* obsolete */ |
| NL80211_EXT_FEATURE_EXT_KEY_ID, |
| NL80211_EXT_FEATURE_STA_TX_PWR, |
| NL80211_EXT_FEATURE_SAE_OFFLOAD, |
| @@ -6499,6 +6639,8 @@ enum nl80211_ext_feature_index { |
| NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA, |
| NL80211_EXT_FEATURE_OWE_OFFLOAD, |
| NL80211_EXT_FEATURE_OWE_OFFLOAD_AP, |
| + NL80211_EXT_FEATURE_DFS_CONCURRENT, |
| + NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT, |
| |
| /* add new features before the definition below */ |
| NUM_NL80211_EXT_FEATURES, |
| @@ -6583,7 +6725,7 @@ enum nl80211_timeout_reason { |
| * request parameters IE in the probe request |
| * @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses |
| * @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at |
| - * rate of at least 5.5M. In case non OCE AP is discovered in the channel, |
| + * rate of at least 5.5M. In case non-OCE AP is discovered in the channel, |
| * only the first probe req in the channel will be sent in high rate. |
| * @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request |
| * tx deferral (dot11FILSProbeDelay shall be set to 15ms) |
| @@ -6619,7 +6761,7 @@ enum nl80211_timeout_reason { |
| * received on the 2.4/5 GHz channels to actively scan only the 6GHz |
| * channels on which APs are expected to be found. Note that when not set, |
| * the scan logic would scan all 6GHz channels, but since transmission of |
| - * probe requests on non PSC channels is limited, it is highly likely that |
| + * probe requests on non-PSC channels is limited, it is highly likely that |
| * these channels would passively be scanned. Also note that when the flag |
| * is set, in addition to the colocated APs, PSC channels would also be |
| * scanned if the user space has asked for it. |
| @@ -6669,6 +6811,8 @@ enum nl80211_acl_policy { |
| * @NL80211_SMPS_STATIC: static SMPS (use a single antenna) |
| * @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and |
| * turn on other antennas after CTS/RTS). |
| + * @__NL80211_SMPS_AFTER_LAST: internal |
| + * @NL80211_SMPS_MAX: highest used enumeration |
| */ |
| enum nl80211_smps_mode { |
| NL80211_SMPS_OFF, |
| @@ -6890,6 +7034,8 @@ enum nl80211_bss_select_attr { |
| * @NL80211_NAN_FUNC_PUBLISH: function is publish |
| * @NL80211_NAN_FUNC_SUBSCRIBE: function is subscribe |
| * @NL80211_NAN_FUNC_FOLLOW_UP: function is follow-up |
| + * @__NL80211_NAN_FUNC_TYPE_AFTER_LAST: internal use |
| + * @NL80211_NAN_FUNC_MAX_TYPE: internal use |
| */ |
| enum nl80211_nan_function_type { |
| NL80211_NAN_FUNC_PUBLISH, |
| @@ -6951,7 +7097,7 @@ enum nl80211_nan_func_term_reason { |
| * The instance ID for the follow up Service Discovery Frame. This is u8. |
| * @NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID: relevant if the function's type |
| * is follow up. This is a u8. |
| - * The requestor instance ID for the follow up Service Discovery Frame. |
| + * The requester instance ID for the follow up Service Discovery Frame. |
| * @NL80211_NAN_FUNC_FOLLOW_UP_DEST: the MAC address of the recipient of the |
| * follow up Service Discovery Frame. This is a binary attribute. |
| * @NL80211_NAN_FUNC_CLOSE_RANGE: is this function limited for devices in a |
| @@ -7050,7 +7196,7 @@ enum nl80211_nan_match_attributes { |
| }; |
| |
| /** |
| - * nl80211_external_auth_action - Action to perform with external |
| + * enum nl80211_external_auth_action - Action to perform with external |
| * authentication request. Used by NL80211_ATTR_EXTERNAL_AUTH_ACTION. |
| * @NL80211_EXTERNAL_AUTH_START: Start the authentication. |
| * @NL80211_EXTERNAL_AUTH_ABORT: Abort the ongoing authentication. |
| @@ -7068,7 +7214,7 @@ enum nl80211_external_auth_action { |
| * @NL80211_FTM_RESP_ATTR_LCI: The content of Measurement Report Element |
| * (9.4.2.22 in 802.11-2016) with type 8 - LCI (9.4.2.22.10), |
| * i.e. starting with the measurement token |
| - * @NL80211_FTM_RESP_ATTR_CIVIC: The content of Measurement Report Element |
| + * @NL80211_FTM_RESP_ATTR_CIVICLOC: The content of Measurement Report Element |
| * (9.4.2.22 in 802.11-2016) with type 11 - Civic (Section 9.4.2.22.13), |
| * i.e. starting with the measurement token |
| * @__NL80211_FTM_RESP_ATTR_LAST: Internal |
| @@ -7341,7 +7487,7 @@ enum nl80211_peer_measurement_attrs { |
| * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if |
| * trigger based ranging measurement is supported |
| * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating |
| - * if non trigger based ranging measurement is supported |
| + * if non-trigger-based ranging measurement is supported |
| * |
| * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal |
| * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number |
| @@ -7395,7 +7541,7 @@ enum nl80211_peer_measurement_ftm_capa { |
| * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor |
| * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based |
| * ranging will be used. |
| - * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based |
| + * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non-trigger-based |
| * ranging measurement (flag) |
| * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are |
| * mutually exclusive. |
| @@ -7473,7 +7619,7 @@ enum nl80211_peer_measurement_ftm_failure_reasons { |
| * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames |
| * transmitted (u32, optional) |
| * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames |
| - * that were acknowleged (u32, optional) |
| + * that were acknowledged (u32, optional) |
| * @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the |
| * busy peer (u32, seconds) |
| * @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent |
| @@ -7711,6 +7857,7 @@ enum nl80211_sae_pwe_mechanism { |
| * |
| * @NL80211_SAR_TYPE_POWER: power limitation specified in 0.25dBm unit |
| * |
| + * @NUM_NL80211_SAR_TYPE: internal |
| */ |
| enum nl80211_sar_type { |
| NL80211_SAR_TYPE_POWER, |
| @@ -7724,6 +7871,8 @@ enum nl80211_sar_type { |
| /** |
| * enum nl80211_sar_attrs - Attributes for SAR spec |
| * |
| + * @__NL80211_SAR_ATTR_INVALID: Invalid |
| + * |
| * @NL80211_SAR_ATTR_TYPE: the SAR type as defined in &enum nl80211_sar_type. |
| * |
| * @NL80211_SAR_ATTR_SPECS: Nested array of SAR power |
| @@ -7755,6 +7904,8 @@ enum nl80211_sar_attrs { |
| /** |
| * enum nl80211_sar_specs_attrs - Attributes for SAR power limit specs |
| * |
| + * @__NL80211_SAR_ATTR_SPECS_INVALID: Invalid |
| + * |
| * @NL80211_SAR_ATTR_SPECS_POWER: Required (s32)value to specify the actual |
| * power limit value in units of 0.25 dBm if type is |
| * NL80211_SAR_TYPE_POWER. (i.e., a value of 44 represents 11 dBm). |
| @@ -7869,4 +8020,54 @@ enum nl80211_ap_settings_flags { |
| NL80211_AP_SETTINGS_SA_QUERY_OFFLOAD_SUPPORT = 1 << 1, |
| }; |
| |
| +/** |
| + * enum nl80211_wiphy_radio_attrs - wiphy radio attributes |
| + * |
| + * @__NL80211_WIPHY_RADIO_ATTR_INVALID: Invalid |
| + * |
| + * @NL80211_WIPHY_RADIO_ATTR_INDEX: Index of this radio (u32) |
| + * @NL80211_WIPHY_RADIO_ATTR_FREQ_RANGE: Frequency range supported by this |
| + * radio. Attribute may be present multiple times. |
| + * @NL80211_WIPHY_RADIO_ATTR_INTERFACE_COMBINATION: Supported interface |
| + * combination for this radio. Attribute may be present multiple times |
| + * and contains attributes defined in &enum nl80211_if_combination_attrs. |
| + * |
| + * @__NL80211_WIPHY_RADIO_ATTR_LAST: Internal |
| + * @NL80211_WIPHY_RADIO_ATTR_MAX: Highest attribute |
| + */ |
| +enum nl80211_wiphy_radio_attrs { |
| + __NL80211_WIPHY_RADIO_ATTR_INVALID, |
| + |
| + NL80211_WIPHY_RADIO_ATTR_INDEX, |
| + NL80211_WIPHY_RADIO_ATTR_FREQ_RANGE, |
| + NL80211_WIPHY_RADIO_ATTR_INTERFACE_COMBINATION, |
| + |
| + /* keep last */ |
| + __NL80211_WIPHY_RADIO_ATTR_LAST, |
| + NL80211_WIPHY_RADIO_ATTR_MAX = __NL80211_WIPHY_RADIO_ATTR_LAST - 1, |
| +}; |
| + |
| +/** |
| + * enum nl80211_wiphy_radio_freq_range - wiphy radio frequency range |
| + * |
| + * @__NL80211_WIPHY_RADIO_FREQ_ATTR_INVALID: Invalid |
| + * |
| + * @NL80211_WIPHY_RADIO_FREQ_ATTR_START: Frequency range start (u32). |
| + * The unit is kHz. |
| + * @NL80211_WIPHY_RADIO_FREQ_ATTR_END: Frequency range end (u32). |
| + * The unit is kHz. |
| + * |
| + * @__NL80211_WIPHY_RADIO_FREQ_ATTR_LAST: Internal |
| + * @NL80211_WIPHY_RADIO_FREQ_ATTR_MAX: Highest attribute |
| + */ |
| +enum nl80211_wiphy_radio_freq_range { |
| + __NL80211_WIPHY_RADIO_FREQ_ATTR_INVALID, |
| + |
| + NL80211_WIPHY_RADIO_FREQ_ATTR_START, |
| + NL80211_WIPHY_RADIO_FREQ_ATTR_END, |
| + |
| + __NL80211_WIPHY_RADIO_FREQ_ATTR_LAST, |
| + NL80211_WIPHY_RADIO_FREQ_ATTR_MAX = __NL80211_WIPHY_RADIO_FREQ_ATTR_LAST - 1, |
| +}; |
| + |
| #endif /* __LINUX_NL80211_H */ |
| -- |
| 2.18.0 |
| |