blob: a00dbb5ff034f65d0a9ba849606cf654647cf8cc [file] [log] [blame]
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +02001TF-A Build Instructions
2======================
3
4This section describes how to compile the ARM Trusted Firmware (TF-A) project for Marvell's platforms.
5
6Build Instructions
7------------------
8(1) Set the cross compiler::
9
10 > export CROSS_COMPILE=/path/to/toolchain/aarch64-linux-gnu-
11
12(2) Set path for FIP images:
13
14 Set U-Boot image path (relatively to TF-A root or absolute path)::
15
16 > export BL33=path/to/u-boot.bin
17
18 For example: if U-Boot project (and its images) is located at ~/project/u-boot,
19 BL33 should be ~/project/u-boot/u-boot.bin
20
21 .. note::
22
23 u-boot.bin should be used and not u-boot-spl.bin
24
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030025 Set MSS/SCP image path (mandatory only for Armada80x0)::
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020026
27 > export SCP_BL2=path/to/mrvl_scp_bl2*.img
28
29(3) Armada-37x0 build requires WTP tools installation.
30
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030031 See below in the section "Tools and external components installation".
32 Install ARM 32-bit cross compiler, which is required for building WTMI image for CM3::
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020033
34 > sudo apt-get install gcc-arm-linux-gnueabi
35
36(4) Clean previous build residuals (if any)::
37
38 > make distclean
39
40(5) Build TF-A:
41
42 There are several build options:
43
44 - DEBUG: default is without debug information (=0). in order to enable it use DEBUG=1
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030045 Must be disabled when building UART recovery images due to current console driver
46 implementation that is not compatible with Xmodem protocol used for boot image download.
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020047
48 - LOG_LEVEL: defines the level of logging which will be purged to the default output port.
49
50 LOG_LEVEL_NONE 0
51 LOG_LEVEL_ERROR 10
52 LOG_LEVEL_NOTICE 20
53 LOG_LEVEL_WARNING 30
54 LOG_LEVEL_INFO 40
55 LOG_LEVEL_VERBOSE 50
56
57 - USE_COHERENT_MEM: This flag determines whether to include the coherent memory region in the
58 BL memory map or not.
59
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030060 - LLC_ENABLE: Flag defining the LLC (L3) cache state. The cache is enabled by default (LLC_ENABLE=1).
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020061
62 - MARVELL_SECURE_BOOT: build trusted(=1)/non trusted(=0) image, default is non trusted.
63
64 - BLE_PATH:
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030065 Points to BLE (Binary ROM extension) sources folder. Only required for A8K builds.
Konstantin Porotchkin01851db2018-10-03 14:21:42 +030066 The parameter is optional, its default value is "plat/marvell/a8k/common/ble".
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020067
68 - MV_DDR_PATH:
69 For A7/8K, use this parameter to point to mv_ddr driver sources to allow BLE build. For A37x0,
70 it is used for ddr_tool build.
71 Usage example: MV_DDR_PATH=path/to/mv_ddr
72 The parameter is optional for A7/8K, when this parameter is not set, the mv_ddr
73 sources are expected to be located at: drivers/marvell/mv_ddr. However, the parameter
74 is necessary for A37x0.
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030075 For the mv_ddr source location, check the section "Tools and external components installation"
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020076
77 - DDR_TOPOLOGY: For Armada37x0 only, the DDR topology map index/name, default is 0.
78 Supported Options:
79 - DDR3 1CS (0): DB-88F3720-DDR3-Modular (512MB); EspressoBIN (512MB)
80 - DDR4 1CS (1): DB-88F3720-DDR4-Modular (512MB)
Konstantin Porotchkin569b3b92018-11-25 16:18:06 +020081 - DDR3 2CS (2): EspressoBIN V3-V5 (1GB)
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020082 - DDR4 2CS (3): DB-88F3720-DDR4-Modular (4GB)
83 - DDR3 1CS (4): DB-88F3720-DDR3-Modular (1GB)
Konstantin Porotchkin569b3b92018-11-25 16:18:06 +020084 - DDR4 1CS (5): EspressoBin V7 (1GB)
85 - DDR4 2CS (6): EspressoBin V7 (2GB)
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020086 - CUSTOMER (CUST): Customer board, DDR3 1CS 512MB
87
88 - CLOCKSPRESET: For Armada37x0 only, the clock tree configuration preset including CPU and DDR frequency,
89 default is CPU_800_DDR_800.
90 - CPU_600_DDR_600 - CPU at 600 MHz, DDR at 600 MHz
91 - CPU_800_DDR_800 - CPU at 800 MHz, DDR at 800 MHz
92 - CPU_1000_DDR_800 - CPU at 1000 MHz, DDR at 800 MHz
93 - CPU_1200_DDR_750 - CPU at 1200 MHz, DDR at 750 MHz
94
95 - BOOTDEV: For Armada37x0 only, the flash boot device, default is SPINOR,
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030096 Currently, Armada37x0 only supports SPINOR, SPINAND, EMMCNORM and SATA:
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +020097
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +030098 - SPINOR - SPI NOR flash boot
99 - SPINAND - SPI NAND flash boot
100 - EMMCNORM - eMMC Download Mode
101 Download boot loader or program code from eMMC flash into CM3 or CA53
102 Requires full initialization and command sequence
103 - SATA - SATA device boot
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200104
105 - PARTNUM: For Armada37x0 only, the boot partition number, default is 0. To boot from eMMC, the value
106 should be aligned with the parameter in U-Boot with name of CONFIG_SYS_MMC_ENV_PART, whose
107 value by default is 1.
108 For details about CONFIG_SYS_MMC_ENV_PART, please refer to the U-Boot build instructions.
109
110 - WTMI_IMG: For Armada37x0 only, the path of the WTMI image can point to an image which does
111 nothing, an image which supports EFUSE or a customized CM3 firmware binary. The default image
112 is wtmi.bin that built from sources in WTP folder, which is the next option. If the default
113 image is OK, then this option should be skipped.
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300114
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200115 - WTP: For Armada37x0 only, use this parameter to point to wtptools source code directory, which
116 can be found as a3700_utils.zip in the release.
117 Usage example: WTP=/path/to/a3700_utils
118
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200119 For example, in order to build the image in debug mode with log level up to 'notice' level run::
120
121 > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 PLAT=<MARVELL_PLATFORM> all fip
122
123 And if we want to build a Armada37x0 image in debug mode with log level up to 'notice' level,
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300124 the image has the preset CPU at 1000 MHz, preset DDR3 at 800 MHz, the DDR topology of DDR4 2CS,
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200125 the image boot from SPI NOR flash partition 0, and the image is non trusted in WTP, the command
126 line is as following::
127
128 > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 SECURE=0 CLOCKSPRESET=CPU_1000_DDR_800 \
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300129 DDR_TOPOLOGY=3 BOOTDEV=SPINOR PARTNUM=0 PLAT=a3700 all fip
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200130
131 Supported MARVELL_PLATFORM are:
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300132 - a3700 (for both A3720 DB and EspressoBin)
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200133 - a70x0
134 - a70x0_amc (for AMC board)
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200135 - a80x0
136 - a80x0_mcbin (for MacciatoBin)
137
138Special Build Flags
139--------------------
140 - PLAT_RECOVERY_IMAGE_ENABLE: When set this option to enable secondary recovery function when build
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300141 atf. In order to build UART recovery image this operation should be disabled for a70x0 and a80x0
Konstantin Porotchkin01851db2018-10-03 14:21:42 +0300142 because of hardware limitation (boot from secondary image can interrupt UART recovery process).
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200143 This MACRO definition is set in plat/marvell/a8k/common/include/platform_def.h file
144
145(for more information about build options, please refer to section 'Summary of build options' in TF-A user-guide:
146 https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/user-guide.md)
147
148
149Build output
150-------------
151Marvell's TF-A compilation generates 7 files:
152 - ble.bin - BLe image
153 - bl1.bin - BL1 image
154 - bl2.bin - BL2 image
155 - bl31.bin - BL31 image
156 - fip.bin - FIP image (contains BL2, BL31 & BL33 (U-Boot) images)
157 - boot-image.bin - TF-A image (contains BL1 and FIP images)
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300158 - flash-image.bin - Image which contains boot-image.bin and SPL image;
159 should be placed on the boot flash/device.
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200160
161
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300162Tools and external components installation
163==========================================
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200164
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300165Armada37x0 Builds require installation of 3 components
166-------------------------------------------------------
167
168(1) ARM cross compiler capable of building images for the service CPU (CM3).
169 This component is usually included in the Linux host packages.
Ding Tao36cb6682018-12-10 09:31:23 +0000170 On Debian/Ubuntu hosts the default GNU ARM tool chain can be installed
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300171 using the following command::
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200172
173 > sudo apt-get install gcc-arm-linux-gnueabi
174
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300175 Only if required, the default tool chain prefix "arm-linux-gnueabi-" can be
176 overwritten using the environment variable CROSS_CM3.
177 Example for BASH shell::
Konstantin Porotchkinaf3d5292018-02-26 16:32:35 +0200178
179 > export CROSS_CM3=/opt/arm-cross/bin/arm-linux-gnueabi
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300180
181(2) DDR initialization library sources (mv_ddr) available at the following repository
182 (use the "mv_ddr-armada-atf-mainline" branch)::
183 https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git
184
185(3) Armada3700 tools available at the following repository (use the latest release branch)::
186 https://github.com/MarvellEmbeddedProcessors/A3700-utils-marvell.git
187
Konstantin Porotchkin01851db2018-10-03 14:21:42 +0300188Armada70x0 and Armada80x0 Builds require installation of an additional component
189--------------------------------------------------------------------------------
Konstantin Porotchkinab9ceeb2018-07-29 11:53:32 +0300190
191(1) DDR initialization library sources (mv_ddr) available at the following repository
192 (use the "mv_ddr-armada-atf-mainline" branch)::
193 https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git
194