/*
 * Copyright (c) 2015-2018, ARM Limited and Contributors. All rights reserved.
 *
 * SPDX-License-Identifier: BSD-3-Clause
 */

#ifndef UART_16550_H
#define UART_16550_H

#include <drivers/console.h>

/* UART16550 Registers */
#define UARTTX			0x0
#define UARTRX			0x0
#define UARTDLL			0x0
#define UARTIER			0x4
#define UARTDLLM		0x4
#define UARTIIR			0x8
#define UARTFCR			0x8
#define UARTLCR			0xc
#define UARTMCR			0x10
#define UARTLSR			0x14
#define UARTMSR			0x18
#define UARTSPR			0x1c
#define UARTCSR			0x20
/* Some instances have MDR1 defined as well */
#define UARTMDR1		0x20
#define UARTRXFIFOCFG		0x24
#define UARTMIE			0x28
#define UARTVNDR		0x2c
#define UARTASR			0x3c

/* FIFO Control Register bits */
#define UARTFCR_FIFOMD_16450	(0 << 6)
#define UARTFCR_FIFOMD_16550	(1 << 6)
#define UARTFCR_RXTRIG_1	(0 << 6)
#define UARTFCR_RXTRIG_4	(1 << 6)
#define UARTFCR_RXTRIG_8	(2 << 6)
#define UARTFCR_RXTRIG_16	(3 << 6)
#define UARTFCR_TXTRIG_1	(0 << 4)
#define UARTFCR_TXTRIG_4	(1 << 4)
#define UARTFCR_TXTRIG_8	(2 << 4)
#define UARTFCR_TXTRIG_16	(3 << 4)
#define UARTFCR_DMAEN		(1 << 3)	/* Enable DMA mode */
#define UARTFCR_TXCLR		(1 << 2)	/* Clear contents of Tx FIFO */
#define UARTFCR_RXCLR		(1 << 1)	/* Clear contents of Rx FIFO */
#define UARTFCR_FIFOEN		(1 << 0)	/* Enable the Tx/Rx FIFO */

/* Line Control Register bits */
#define UARTLCR_DLAB		(1 << 7)	/* Divisor Latch Access */
#define UARTLCR_SETB		(1 << 6)	/* Set BREAK Condition */
#define UARTLCR_SETP		(1 << 5)	/* Set Parity to LCR[4] */
#define UARTLCR_EVEN		(1 << 4)	/* Even Parity Format */
#define UARTLCR_PAR		(1 << 3)	/* Parity */
#define UARTLCR_STOP		(1 << 2)	/* Stop Bit */
#define UARTLCR_WORDSZ_5	0		/* Word Length of 5 */
#define UARTLCR_WORDSZ_6	1		/* Word Length of 6 */
#define UARTLCR_WORDSZ_7	2		/* Word Length of 7 */
#define UARTLCR_WORDSZ_8	3		/* Word Length of 8 */

/* Line Status Register bits */
#define UARTLSR_RXFIFOEMT	(1 << 9)	/* Rx Fifo Empty */
#define UARTLSR_TXFIFOFULL	(1 << 8)	/* Tx Fifo Full */
#define UARTLSR_RXFIFOERR	(1 << 7)	/* Rx Fifo Error */
#define UARTLSR_TEMT		(1 << 6)	/* Tx Shift Register Empty */
#define UARTLSR_THRE		(1 << 5)	/* Tx Holding Register Empty */
#define UARTLSR_BRK		(1 << 4)	/* Break Condition Detected */
#define UARTLSR_FERR		(1 << 3)	/* Framing Error */
#define UARTLSR_PERR		(1 << 3)	/* Parity Error */
#define UARTLSR_OVRF		(1 << 2)	/* Rx Overrun Error */
#define UARTLSR_RDR_BIT		(0)		/* Rx Data Ready Bit */
#define UARTLSR_RDR		(1 << UARTLSR_RDR_BIT)	/* Rx Data Ready */

#ifndef __ASSEMBLER__

#include <stdint.h>

/*
 * Initialize a new 16550 console instance and register it with the console
 * framework. The |console| pointer must point to storage that will be valid
 * for the lifetime of the console, such as a global or static local variable.
 * Its contents will be reinitialized from scratch.
 * When |clock| has a value of 0, the UART will *not* be initialised. This
 * means the UART should already be enabled and the baudrate and clock setup
 * should have been done already, either by platform specific code or by
 * previous firmware stages. The |baud| parameter will be ignored in this
 * case as well.
 */
int console_16550_register(uintptr_t baseaddr, uint32_t clock, uint32_t baud,
			   console_t *console);

#endif /*__ASSEMBLER__*/

#endif /* UART_16550_H */