feat(tc): factor in FVP/FPGA differences
Even though the FVP and FPGA are meant to be identical their RoS's (rest
of system) are different. Factor these in so the device tree works for
both. The differences are:
* addresses of GIC and UART
* displays (FPGA uses 4k)
* ethernet devices and SD card (it's non removable on the FPGA)
Their frequencies are also different. The FVP simulates certain
frequencies but isn't very sensitive when we disregard them. To keep
code similar, update them with the FPGA values. This keeps working on
FVP even if slightly incorrect.
Also add an option for the DPU to either use fixed clocks or SCMI set
clocks, hidden behind a flag. This is useful during bringup and because
SCMI may not necessarily work on FPGA.
Co-developed-by: Kshitij Sisodia <kshitij.sisodia@arm.com>
Co-developed-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Co-developed-by: Usama Arif <usama.arif@arm.com>
Co-developed-by: Angel Rodriguez Garcia <angel.rodriguezgarcia@arm.com>
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Change-Id: Ic7a4bfc302673a3a6571757e23a9e6184fba2a13
diff --git a/fdts/tc.dts b/fdts/tc.dts
index fc953a3..6eb7d8a 100644
--- a/fdts/tc.dts
+++ b/fdts/tc.dts
@@ -22,7 +22,7 @@
};
chosen {
- stdout-path = "serial0:115200n8";
+ stdout-path = STDOUT_PATH;
};
cpus {
@@ -411,7 +411,7 @@
};
};
- gic: interrupt-controller@2c010000 {
+ gic: interrupt-controller@GIC_CTRL_ADDR {
compatible = "arm,gic-v3";
#address-cells = <2>;
#interrupt-cells = <3>;
@@ -419,7 +419,7 @@
ranges;
interrupt-controller;
reg = <0x0 0x30000000 0 0x10000>, /* GICD */
- <0x0 0x30080000 0 0x200000>; /* GICR */
+ <0x0 0x30080000 0 GIC_GICR_OFFSET>; /* GICR */
interrupts = <GIC_PPI 0x9 IRQ_TYPE_LEVEL_LOW>;
};
@@ -434,7 +434,7 @@
soc_refclk: refclk {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency = <100000000>;
+ clock-frequency = <1000000000>;
clock-output-names = "apb_pclk";
};
@@ -452,9 +452,10 @@
clock-output-names = "uartclk";
};
+ /* soc_uart0 on FPGA, ap_ns_uart on FVP */
os_uart: serial@2a400000 {
compatible = "arm,pl011", "arm,primecell";
- reg = <0x0 0x2A400000 0x0 0x1000>;
+ reg = <0x0 0x2A400000 0x0 UART_OFFSET>;
interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&soc_uartclk>, <&soc_refclk>;
clock-names = "uartclk", "apb_pclk";
@@ -479,24 +480,21 @@
display-timings {
timing-panel {
- clock-frequency = <25175000>;
- hactive = <640>;
- vactive = <480>;
- hfront-porch = <16>;
- hback-porch = <48>;
- hsync-len = <96>;
- vfront-porch = <10>;
- vback-porch = <33>;
- vsync-len = <2>;
+ VENCODER_TIMING;
};
};
};
ethernet@18000000 {
- compatible = "smsc,lan91c111";
+ compatible = ETH_COMPATIBLE;
reg = <0x0 0x18000000 0x0 0x10000>;
interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+
+ /* FPGA only but will work on FVP. Keep for simplicity */
+ phy-mode = "mii";
+ reg-io-width = <2>;
+ smsc,irq-push-pull;
};
kmi@1c060000 {
@@ -549,10 +547,10 @@
reg = <0x0 0x001c050000 0x0 0x1000>;
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
- cd-gpios = <&sysreg 0 0>;
+ MMC_REMOVABLE;
wp-gpios = <&sysreg 1 0>;
- bus-width = <8>;
- max-frequency = <12000000>;
+ bus-width = <4>;
+ max-frequency = <25000000>;
vmmc-supply = <&fixed_3v3>;
clocks = <&bp_clock24mhz>, <&bp_clock24mhz>;
clock-names = "mclk", "apb_pclk";
@@ -614,14 +612,12 @@
reg = <0 0x2cc00000 0 0x20000>;
interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "DPU";
- clocks = <&scmi_clk 0>;
- clock-names = "aclk";
+ DPU_CLK_ATTR1;
iommus = <&smmu_700 0x100>;
power-domains = <&scmi_devpd DPU_SCMI_PD_IDX>;
pl0: pipeline@0 {
reg = <0>;
- clocks = <&scmi_clk 1>;
- clock-names = "pxclk";
+ DPU_CLK_ATTR2;
pl_id = <0>;
ports {
#address-cells = <1>;
@@ -637,8 +633,7 @@
pl1: pipeline@1 {
reg = <1>;
- clocks = <&scmi_clk 2>;
- clock-names = "pxclk";
+ DPU_CLK_ATTR3;
pl_id = <1>;
ports {
#address-cells = <1>;