mediatek: mt8183: add mcsi driver
add mcsi driver to support cache coherence.
Change-Id: I94f5922783e5dbc6b7e92aa06464bc1f0177f00a
diff --git a/plat/mediatek/mt8183/drivers/mcsi/mcsi.h b/plat/mediatek/mt8183/drivers/mcsi/mcsi.h
new file mode 100644
index 0000000..c13e22a
--- /dev/null
+++ b/plat/mediatek/mt8183/drivers/mcsi/mcsi.h
@@ -0,0 +1,116 @@
+/*
+ * Copyright (c) 2019, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef MCSI_H
+#define MCSI_H
+
+#define SLAVE_IFACE7_OFFSET 0x1700
+#define SLAVE_IFACE6_OFFSET 0x1600
+#define SLAVE_IFACE5_OFFSET 0x1500
+#define SLAVE_IFACE4_OFFSET 0x1400
+#define SLAVE_IFACE3_OFFSET 0x1300
+#define SLAVE_IFACE2_OFFSET 0x1200
+#define SLAVE_IFACE1_OFFSET 0x1100
+#define SLAVE_IFACE0_OFFSET 0x1000
+#define SLAVE_IFACE_OFFSET(index) (SLAVE_IFACE0_OFFSET + \
+ (0x100 * (index)))
+/* Control and ID register offsets */
+#define CENTRAL_CTRL_REG 0x0
+#define ERR_FLAG_REG 0x4
+#define SF_INIT_REG 0x10
+#define SF_CTRL_REG 0x14
+#define DCM_CTRL_REG 0x18
+#define ERR_FLAG2_REG 0x20
+#define SNP_PENDING_REG 0x28
+#define ACP_PENDING_REG 0x2c
+#define FLUSH_SF 0x500
+#define SYS_CCE_CTRL 0x2000
+#define MST1_CTRL 0x2100
+#define MTS2_CTRL 0x2200
+#define XBAR_ARAW_ARB 0x3000
+#define XBAR_R_ARB 0x3004
+
+/* Slave interface register offsets */
+#define SNOOP_CTRL_REG 0x0
+#define QOS_CTRL_REG 0x4
+#define QOS_OVERRIDE_REG 0x8
+#define QOS_TARGET_REG 0xc
+#define BD_CTRL_REG 0x40
+
+/* Snoop Control register bit definitions */
+#define DVM_SUPPORT (1 << 31)
+#define SNP_SUPPORT (1 << 30)
+#define SHAREABLE_OVWRT (1 << 2)
+#define DVM_EN_BIT (1 << 1)
+#define SNOOP_EN_BIT (1 << 0)
+#define SF2_INIT_DONE (1 << 17)
+#define SF1_INIT_DONE (1 << 16)
+#define TRIG_SF2_INIT (1 << 1)
+#define TRIG_SF1_INIT (1 << 0)
+
+/* Status register bit definitions */
+#define SNP_PENDING 31
+
+/* Status bit */
+#define NS_ACC 1
+#define S_ACC 0
+
+/* Central control register bit definitions */
+#define PMU_SECURE_ACC_EN (1 << 4)
+#define INT_EN (1 << 3)
+#define SECURE_ACC_EN (1 << 2)
+#define DVM_DIS (1 << 1)
+#define SNOOP_DIS (1 << 0)
+
+#define MSCI_MEMORY_SZ (0x10000)
+
+#define MCSI_REG_ACCESS_READ (0x0)
+#define MCSI_REG_ACCESS_WRITE (0x1)
+#define MCSI_REG_ACCESS_SET_BITMASK (0x2)
+#define MCSI_REG_ACCESS_CLEAR_BITMASK (0x3)
+
+#define NR_MAX_SLV (7)
+
+/* ICCS */
+#define CACHE_INSTR_EN (1 << 2)
+#define IDLE_CACHE (1 << 3)
+#define USE_SHARED_CACHE (1 << 4)
+#define CACHE_SHARED_PRE_EN (1 << 5)
+#define CACHE_SHARED_POST_EN (1 << 6)
+
+#define ACP_PENDING_MASK (0x1007f)
+
+#define CCI_CLK_CTRL (MCUCFG_BASE + 0x660)
+
+#ifndef __ASSEMBLY__
+
+#include <plat/common/common_def.h>
+#include <stdint.h>
+
+/* Function declarations */
+
+/*
+ * The MCSI driver must be initialized with the base address of the
+ * MCSI device in the platform memory map, and the cluster indices for
+ * the MCSI slave interfaces 3 and 4 respectively. These are the fully
+ * coherent ACE slave interfaces of MCSI.
+ * The cluster indices must either be 0 or 1, corresponding to the level 1
+ * affinity instance of the mpidr representing the cluster. A negative cluster
+ * index indicates that no cluster is present on that slave interface.
+ */
+void mcsi_init(unsigned long cci_base,
+ unsigned int num_cci_masters);
+void mcsi_cache_flush(void);
+
+void cci_enable_cluster_coherency(unsigned long mpidr);
+void cci_disable_cluster_coherency(unsigned long mpidr);
+
+void cci_secure_switch(unsigned int ns);
+void cci_init_sf(void);
+unsigned long cci_reg_access(unsigned int op, unsigned long offset, unsigned long val);
+
+#endif /* __ASSEMBLY__ */
+#endif /* MCSI_H */