Move GIC setup to a separate file
GIC setup code which used to be in bl31_plat_setup.c is now in fvp_gic.c
to simplify future changes to other bootloader stages. This patch moves
code from bl31_plat_setup.c to fvp_gic.c, simplifies the include file
list for bl31_plat_setup.c, moves GIC declarations from the bl31.h header
file into the platform.h, and reworks files according to coding style
guide.
Change-Id: I48d82a4ba33e7114dcc88f9ca98767a06cf8f417
diff --git a/plat/fvp/bl31_plat_setup.c b/plat/fvp/bl31_plat_setup.c
index 6c59e84..49a9369 100644
--- a/plat/fvp/bl31_plat_setup.c
+++ b/plat/fvp/bl31_plat_setup.c
@@ -28,16 +28,7 @@
* POSSIBILITY OF SUCH DAMAGE.
*/
-#include <string.h>
-#include <assert.h>
-#include <arch_helpers.h>
#include <platform.h>
-#include <bl31.h>
-#include <bl_common.h>
-#include <pl011.h>
-#include <bakery_lock.h>
-#include <cci400.h>
-#include <gic.h>
#include <fvp_pwrc.h>
/*******************************************************************************
@@ -137,8 +128,8 @@
{
unsigned int reg_val;
- /* Initialize the gic cpu and distributor interfaces */
- gic_setup();
+ /* Initialize the gic cpu and distributor interfaces */
+ gic_setup();
/*
* TODO: Configure the CLCD before handing control to
@@ -162,7 +153,7 @@
/* Intialize the power controller */
fvp_pwrc_setup();
- /* Topologies are best known to the platform. */
+ /* Topologies are best known to the platform. */
plat_setup_topology();
}
@@ -178,245 +169,3 @@
BL31_COHERENT_RAM_BASE,
BL31_COHERENT_RAM_LIMIT);
}
-
-/*******************************************************************************
- * TODO: Move GIC setup to a separate file in case it is needed by other BL
- * stages or ELs
- * TODO: Revisit if priorities are being set such that no non-secure interrupt
- * can have a higher priority than a secure one as recommended in the GICv2 spec
- *******************************************************************************/
-
-/*******************************************************************************
- * This function does some minimal GICv3 configuration. The Firmware itself does
- * not fully support GICv3 at this time and relies on GICv2 emulation as
- * provided by GICv3. This function allows software (like Linux) in later stages
- * to use full GICv3 features.
- *******************************************************************************/
-void gicv3_cpuif_setup(void)
-{
- unsigned int scr_val, val, base;
-
- /*
- * When CPUs come out of reset they have their GICR_WAKER.ProcessorSleep
- * bit set. In order to allow interrupts to get routed to the CPU we
- * need to clear this bit if set and wait for GICR_WAKER.ChildrenAsleep
- * to clear (GICv3 Architecture specification 5.4.23).
- * GICR_WAKER is NOT banked per CPU, compute the correct base address
- * per CPU.
- *
- * TODO:
- * For GICv4 we also need to adjust the Base address based on
- * GICR_TYPER.VLPIS
- */
- base = BASE_GICR_BASE +
- (platform_get_core_pos(read_mpidr()) << GICR_PCPUBASE_SHIFT);
- val = gicr_read_waker(base);
-
- val &= ~WAKER_PS;
- gicr_write_waker(base, val);
- dsb();
-
- /* We need to wait for ChildrenAsleep to clear. */
- val = gicr_read_waker(base);
- while (val & WAKER_CA) {
- val = gicr_read_waker(base);
- }
-
- /*
- * We need to set SCR_EL3.NS in order to see GICv3 non-secure state.
- * Restore SCR_EL3.NS again before exit.
- */
- scr_val = read_scr();
- write_scr(scr_val | SCR_NS_BIT);
-
- /*
- * By default EL2 and NS-EL1 software should be able to enable GICv3
- * System register access without any configuration at EL3. But it turns
- * out that GICC PMR as set in GICv2 mode does not affect GICv3 mode. So
- * we need to set it here again. In order to do that we need to enable
- * register access. We leave it enabled as it should be fine and might
- * prevent problems with later software trying to access GIC System
- * Registers.
- */
- val = read_icc_sre_el3();
- write_icc_sre_el3(val | ICC_SRE_EN | ICC_SRE_SRE);
-
- val = read_icc_sre_el2();
- write_icc_sre_el2(val | ICC_SRE_EN | ICC_SRE_SRE);
-
- write_icc_pmr_el1(MAX_PRI_VAL);
-
- /* Restore SCR_EL3 */
- write_scr(scr_val);
-}
-
-/*******************************************************************************
- * This function does some minimal GICv3 configuration when cores go
- * down.
- *******************************************************************************/
-void gicv3_cpuif_deactivate(void)
-{
- unsigned int val, base;
-
- /*
- * When taking CPUs down we need to set GICR_WAKER.ProcessorSleep and
- * wait for GICR_WAKER.ChildrenAsleep to get set.
- * (GICv3 Architecture specification 5.4.23).
- * GICR_WAKER is NOT banked per CPU, compute the correct base address
- * per CPU.
- *
- * TODO:
- * For GICv4 we also need to adjust the Base address based on
- * GICR_TYPER.VLPIS
- */
- base = BASE_GICR_BASE +
- (platform_get_core_pos(read_mpidr()) << GICR_PCPUBASE_SHIFT);
- val = gicr_read_waker(base);
- val |= WAKER_PS;
- gicr_write_waker(base, val);
- dsb();
-
- /* We need to wait for ChildrenAsleep to set. */
- val = gicr_read_waker(base);
- while ((val & WAKER_CA) == 0) {
- val = gicr_read_waker(base);
- }
-}
-
-
-/*******************************************************************************
- * Enable secure interrupts and use FIQs to route them. Disable legacy bypass
- * and set the priority mask register to allow all interrupts to trickle in.
- ******************************************************************************/
-void gic_cpuif_setup(unsigned int gicc_base)
-{
- unsigned int val;
-
- val = gicc_read_iidr(gicc_base);
-
- /*
- * If GICv3 we need to do a bit of additional setup. We want to
- * allow default GICv2 behaviour but allow the next stage to
- * enable full gicv3 features.
- */
- if (((val >> GICC_IIDR_ARCH_SHIFT) & GICC_IIDR_ARCH_MASK) >= 3) {
- gicv3_cpuif_setup();
- }
-
- val = ENABLE_GRP0 | FIQ_EN | FIQ_BYP_DIS_GRP0;
- val |= IRQ_BYP_DIS_GRP0 | FIQ_BYP_DIS_GRP1 | IRQ_BYP_DIS_GRP1;
-
- gicc_write_pmr(gicc_base, MAX_PRI_VAL);
- gicc_write_ctlr(gicc_base, val);
-}
-
-/*******************************************************************************
- * Place the cpu interface in a state where it can never make a cpu exit wfi as
- * as result of an asserted interrupt. This is critical for powering down a cpu
- ******************************************************************************/
-void gic_cpuif_deactivate(unsigned int gicc_base)
-{
- unsigned int val;
-
- /* Disable secure, non-secure interrupts and disable their bypass */
- val = gicc_read_ctlr(gicc_base);
- val &= ~(ENABLE_GRP0 | ENABLE_GRP1);
- val |= FIQ_BYP_DIS_GRP1 | FIQ_BYP_DIS_GRP0;
- val |= IRQ_BYP_DIS_GRP0 | IRQ_BYP_DIS_GRP1;
- gicc_write_ctlr(gicc_base, val);
-
- val = gicc_read_iidr(gicc_base);
-
- /*
- * If GICv3 we need to do a bit of additional setup. Make sure the
- * RDIST is put to sleep.
- */
- if (((val >> GICC_IIDR_ARCH_SHIFT) & GICC_IIDR_ARCH_MASK) >= 3) {
- gicv3_cpuif_deactivate();
- }
-}
-
-/*******************************************************************************
- * Per cpu gic distributor setup which will be done by all cpus after a cold
- * boot/hotplug. This marks out the secure interrupts & enables them.
- ******************************************************************************/
-void gic_pcpu_distif_setup(unsigned int gicd_base)
-{
- gicd_write_igroupr(gicd_base, 0, ~0);
-
- gicd_clr_igroupr(gicd_base, IRQ_SEC_PHY_TIMER);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_0);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_1);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_2);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_3);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_4);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_5);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_6);
- gicd_clr_igroupr(gicd_base, IRQ_SEC_SGI_7);
-
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_PHY_TIMER, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_0, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_1, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_2, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_3, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_4, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_5, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_6, MAX_PRI_VAL);
- gicd_set_ipriorityr(gicd_base, IRQ_SEC_SGI_7, MAX_PRI_VAL);
-
- gicd_set_isenabler(gicd_base, IRQ_SEC_PHY_TIMER);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_0);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_1);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_2);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_3);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_4);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_5);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_6);
- gicd_set_isenabler(gicd_base, IRQ_SEC_SGI_7);
-}
-
-/*******************************************************************************
- * Global gic distributor setup which will be done by the primary cpu after a
- * cold boot. It marks out the secure SPIs, PPIs & SGIs and enables them. It
- * then enables the secure GIC distributor interface.
- ******************************************************************************/
-void gic_distif_setup(unsigned int gicd_base)
-{
- unsigned int ctr, num_ints, ctlr;
-
- /* Disable the distributor before going further */
- ctlr = gicd_read_ctlr(gicd_base);
- ctlr &= ~(ENABLE_GRP0 | ENABLE_GRP1);
- gicd_write_ctlr(gicd_base, ctlr);
-
- /*
- * Mark out non-secure interrupts. Calculate number of
- * IGROUPR registers to consider. Will be equal to the
- * number of IT_LINES
- */
- num_ints = gicd_read_typer(gicd_base) & IT_LINES_NO_MASK;
- num_ints++;
- for (ctr = 0; ctr < num_ints; ctr++)
- gicd_write_igroupr(gicd_base, ctr << IGROUPR_SHIFT, ~0);
-
- /* Configure secure interrupts now */
- gicd_clr_igroupr(gicd_base, IRQ_TZ_WDOG);
- gicd_set_ipriorityr(gicd_base, IRQ_TZ_WDOG, MAX_PRI_VAL);
- gicd_set_itargetsr(gicd_base, IRQ_TZ_WDOG,
- platform_get_core_pos(read_mpidr()));
- gicd_set_isenabler(gicd_base, IRQ_TZ_WDOG);
- gic_pcpu_distif_setup(gicd_base);
-
- gicd_write_ctlr(gicd_base, ctlr | ENABLE_GRP0);
-}
-
-void gic_setup(void)
-{
- unsigned int gicd_base, gicc_base;
-
- gicd_base = platform_get_cfgvar(CONFIG_GICD_ADDR);
- gicc_base = platform_get_cfgvar(CONFIG_GICC_ADDR);
-
- gic_cpuif_setup(gicc_base);
- gic_distif_setup(gicd_base);
-}