diff --git a/plat/nxp/soc-ls1043a/ls1043ardb/ddr_init.c b/plat/nxp/soc-ls1043a/ls1043ardb/ddr_init.c
new file mode 100644
index 0000000..2231c18
--- /dev/null
+++ b/plat/nxp/soc-ls1043a/ls1043ardb/ddr_init.c
@@ -0,0 +1,159 @@
+/*
+ * Copyright 2018-2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <string.h>
+
+#include <common/debug.h>
+#include <ddr.h>
+#include <lib/utils.h>
+
+#include <errata.h>
+#include <platform_def.h>
+
+#ifdef CONFIG_STATIC_DDR
+const struct ddr_cfg_regs static_1600 = {
+	.cs[0].config = U(0x80040322),
+	.cs[0].bnds = U(0x7F),
+	.sdram_cfg[0] = U(0xC50C0000),
+	.sdram_cfg[1] = U(0x401100),
+	.timing_cfg[0] = U(0x91550018),
+	.timing_cfg[1] = U(0xBBB48C42),
+	.timing_cfg[2] = U(0x48C111),
+	.timing_cfg[3] = U(0x10C1000),
+	.timing_cfg[4] = U(0x2),
+	.timing_cfg[5] = U(0x3401400),
+	.timing_cfg[7] = U(0x13300000),
+	.timing_cfg[8] = U(0x2115600),
+	.sdram_mode[0] = U(0x3010210),
+	.sdram_mode[9] = U(0x4000000),
+	.sdram_mode[8] = U(0x500),
+	.sdram_mode[2] = U(0x10210),
+	.sdram_mode[10] = U(0x400),
+	.sdram_mode[11] = U(0x4000000),
+	.sdram_mode[4] = U(0x10210),
+	.sdram_mode[12] = U(0x400),
+	.sdram_mode[13] = U(0x4000000),
+	.sdram_mode[6] = U(0x10210),
+	.sdram_mode[14] = U(0x400),
+	.sdram_mode[15] = U(0x4000000),
+	.interval = U(0x18600618),
+	.zq_cntl = U(0x8A090705),
+	.clk_cntl = U(0x3000000),
+	.cdr[0] = U(0x80040000),
+	.cdr[1] = U(0xA181),
+	.wrlvl_cntl[0] = U(0x8675F607),
+	.wrlvl_cntl[1] = U(0x7090807,
+	.wrlvl_cntl[2] = U(0x7070707),
+	.debug[28] = U(0x00700046),
+};
+
+uint64_t board_static_ddr(struct ddr_info *priv)
+{
+	memcpy(&priv->ddr_reg, &static_1600, sizeof(static_1600));
+
+	return ULL(0x80000000);
+}
+
+#else
+static const struct rc_timing rcz[] = {
+	{1600, 12, 7},
+	{}
+};
+
+static const struct board_timing ram[] = {
+	{0x1f, rcz, 0x00020100, 0},
+};
+
+int ddr_board_options(struct ddr_info *priv)
+{
+	int ret;
+	struct memctl_opt *popts = &priv->opt;
+
+	ret = cal_board_params(priv, ram, ARRAY_SIZE(ram));
+	if (ret)
+		return ret;
+
+	popts->cpo_sample = U(0x46);
+	popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
+			  DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+	popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+			  DDR_CDR2_VREF_OVRD(70);	/* Vref = 70% */
+
+	return 0;
+}
+
+/* DDR model number: MT40A512M8HX-093E */
+struct dimm_params ddr_raw_timing = {
+	.n_ranks = U(1),
+	.rank_density = ULL(2147483648),
+	.capacity = ULL(2147483648),
+	.primary_sdram_width = U(32),
+	.n_row_addr = U(15),
+	.n_col_addr = U(10),
+	.bank_group_bits = U(2),
+	.burst_lengths_bitmask = U(0x0c),
+	.tckmin_x_ps = 938,
+	.tckmax_ps = 1500,
+	.caslat_x = U(0x000DFA00),
+	.taa_ps = 13500,
+	.trcd_ps = 13500,
+	.trp_ps = 13500,
+	.tras_ps = 33000,
+	.trc_ps = 46500,
+	.twr_ps = 15000,
+	.trfc1_ps = 260000,
+	.trfc2_ps = 160000,
+	.trfc4_ps = 110000,
+	.tfaw_ps = 21000,
+	.trrds_ps = 3700,
+	.trrdl_ps = 5300,
+	.tccdl_ps = 5355,
+	.refresh_rate_ps = U(7800000),
+	.rc = U(0x1f),
+};
+
+int ddr_get_ddr_params(struct dimm_params *pdimm,
+			    struct ddr_conf *conf)
+{
+	static const char dimm_model[] = "Fixed DDR on board";
+
+	conf->dimm_in_use[0] = 1;
+	memcpy(pdimm, &ddr_raw_timing, sizeof(struct dimm_params));
+	memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+
+	return 1;
+}
+#endif
+
+int64_t init_ddr(void)
+{
+	struct ddr_info info;
+	struct sysinfo sys;
+	int64_t dram_size;
+
+	zeromem(&sys, sizeof(sys));
+	get_clocks(&sys);
+	debug("platform clock %lu\n", sys.freq_platform);
+	debug("DDR PLL1 %lu\n", sys.freq_ddr_pll0);
+	debug("DDR PLL2 %lu\n", sys.freq_ddr_pll1);
+
+	zeromem(&info, sizeof(struct ddr_info));
+	info.num_ctlrs = 1;
+	info.dimm_on_ctlr = 1;
+	info.clk = get_ddr_freq(&sys, 0);
+	info.ddr[0] = (void *)NXP_DDR_ADDR;
+
+	dram_size = dram_init(&info);
+
+	if (dram_size < 0) {
+		ERROR("DDR init failed\n");
+	}
+
+#ifdef ERRATA_SOC_A008850
+	erratum_a008850_post();
+#endif
+	return dram_size;
+}
diff --git a/plat/nxp/soc-ls1043a/ls1043ardb/plat_def.h b/plat/nxp/soc-ls1043a/ls1043ardb/plat_def.h
new file mode 100644
index 0000000..249f457
--- /dev/null
+++ b/plat/nxp/soc-ls1043a/ls1043ardb/plat_def.h
@@ -0,0 +1,79 @@
+/*
+ * Copyright 2018-2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef PLAT_DEF_H
+#define PLAT_DEF_H
+
+#include <arch.h>
+/*
+ * Required without TBBR.
+ * To include the defines for DDR PHY Images.
+ */
+#include <tbbr_img_def.h>
+
+#include "policy.h"
+#include <soc.h>
+
+#define NXP_SPD_EEPROM0		0x51
+
+#define NXP_SYSCLK_FREQ		100000000
+#define NXP_DDRCLK_FREQ		100000000
+
+/* UART related definition */
+#define NXP_CONSOLE_ADDR	NXP_UART_ADDR
+#define NXP_CONSOLE_BAUDRATE	115200
+
+/* Size of cacheable stacks */
+#if defined(IMAGE_BL2)
+#if defined(TRUSTED_BOARD_BOOT)
+#define PLATFORM_STACK_SIZE	0x2000
+#else
+#define PLATFORM_STACK_SIZE	0x1000
+#endif
+#elif defined(IMAGE_BL31)
+#define PLATFORM_STACK_SIZE	0x1000
+#endif
+
+/* SD block buffer */
+#define NXP_SD_BLOCK_BUF_SIZE	(0x00100000)
+#define NXP_SD_BLOCK_BUF_ADDR	ULL(0x80000000)
+
+#define BL2_LIMIT		(NXP_OCRAM_ADDR + NXP_OCRAM_SIZE)
+
+/* IO defines as needed by IO driver framework */
+#define MAX_IO_DEVICES		3
+#define MAX_IO_BLOCK_DEVICES	1
+#define MAX_IO_HANDLES		4
+
+/*
+ * FIP image defines - Offset at which FIP Image would be present
+ * Image would include Bl31 , Bl33 and Bl32 (optional)
+ */
+#ifdef POLICY_FUSE_PROVISION
+#define MAX_FIP_DEVICES		2
+#endif
+
+#ifndef MAX_FIP_DEVICES
+#define MAX_FIP_DEVICES		1
+#endif
+
+/*
+ * ID of the secure physical generic timer interrupt used by the BL32.
+ */
+#define BL32_IRQ_SEC_PHY_TIMER	29
+
+/*
+ * Define properties of Group 1 Secure and Group 0 interrupts as per GICv3
+ * terminology. On a GICv2 system or mode, the lists will be merged and treated
+ * as Group 0 interrupts.
+ */
+#define PLAT_LS_G1S_IRQ_PROPS(grp) \
+	INTR_PROP_DESC(BL32_IRQ_SEC_PHY_TIMER, GIC_HIGHEST_SEC_PRIORITY, grp, \
+			GIC_INTR_CFG_LEVEL)
+
+#define PLAT_LS_G0_IRQ_PROPS(grp)
+
+#endif /* PLAT_DEF_H */
diff --git a/plat/nxp/soc-ls1043a/ls1043ardb/platform.c b/plat/nxp/soc-ls1043a/ls1043ardb/platform.c
new file mode 100644
index 0000000..65d508c
--- /dev/null
+++ b/plat/nxp/soc-ls1043a/ls1043ardb/platform.c
@@ -0,0 +1,28 @@
+/*
+ * Copyright 2020-2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <plat_common.h>
+
+#pragma weak board_enable_povdd
+#pragma weak board_disable_povdd
+
+bool board_enable_povdd(void)
+{
+#ifdef CONFIG_POVDD_ENABLE
+	return true;
+#else
+	return false;
+#endif
+}
+
+bool board_disable_povdd(void)
+{
+#ifdef CONFIG_POVDD_ENABLE
+	return true;
+#else
+	return false;
+#endif
+}
diff --git a/plat/nxp/soc-ls1043a/ls1043ardb/platform.mk b/plat/nxp/soc-ls1043a/ls1043ardb/platform.mk
new file mode 100644
index 0000000..5d23356
--- /dev/null
+++ b/plat/nxp/soc-ls1043a/ls1043ardb/platform.mk
@@ -0,0 +1,40 @@
+#
+# Copyright 2018-2021 NXP
+#
+# SPDX-License-Identifier: BSD-3-Clause
+#
+
+# board-specific build parameters
+
+BOOT_MODE		?=	nor
+BOARD			:=	ls1043ardb
+POVDD_ENABLE		:=	no
+
+# DDR Compilation Configs
+CONFIG_DDR_NODIMM	:=	1
+NUM_OF_DDRC		:=	1
+DDRC_NUM_DIMM		:=	0
+DDRC_NUM_CS		:=	4
+DDR_ECC_EN		:=	no
+CONFIG_STATIC_DDR 	:=	0
+
+# On-Board Flash Details
+# 128MB IFC NOR Flash
+NOR_FLASH_SZ		:=	0x8000000
+
+# Platform specific features.
+WARM_BOOT		:=	no
+
+# Adding Platform files build files
+BL2_SOURCES	+=	${BOARD_PATH}/ddr_init.c\
+			${BOARD_PATH}/platform.c
+
+SUPPORTED_BOOT_MODE	:=	nor	\
+				sd	\
+				nand
+
+# Adding platform board build info
+include plat/nxp/common/plat_make_helper/plat_common_def.mk
+
+# Adding SoC build info
+include plat/nxp/soc-ls1043a/soc.mk
diff --git a/plat/nxp/soc-ls1043a/ls1043ardb/platform_def.h b/plat/nxp/soc-ls1043a/ls1043ardb/platform_def.h
new file mode 100644
index 0000000..4721a32
--- /dev/null
+++ b/plat/nxp/soc-ls1043a/ls1043ardb/platform_def.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2018-2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef PLATFORM_DEF_H
+#define PLATFORM_DEF_H
+
+#include <plat_def.h>
+#include <plat_default_def.h>
+
+#endif /* PLATFORM_DEF_H */
diff --git a/plat/nxp/soc-ls1043a/ls1043ardb/policy.h b/plat/nxp/soc-ls1043a/ls1043ardb/policy.h
new file mode 100644
index 0000000..843b5e2
--- /dev/null
+++ b/plat/nxp/soc-ls1043a/ls1043ardb/policy.h
@@ -0,0 +1,16 @@
+/*
+ * Copyright 2018-2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef POLICY_H
+#define	POLICY_H
+
+/*
+ * Set this to 0x0 to leave the default SMMU page size in sACR
+ * Set this to 0x1 to change the SMMU page size to 64K
+ */
+#define POLICY_SMMU_PAGESZ_64K	0x1
+
+#endif /* POLICY_H */