diff --git a/drivers/marvell/comphy/phy-comphy-cp110.c b/drivers/marvell/comphy/phy-comphy-cp110.c
index e9dcfb8..d1c26f8 100644
--- a/drivers/marvell/comphy/phy-comphy-cp110.c
+++ b/drivers/marvell/comphy/phy-comphy-cp110.c
@@ -1922,6 +1922,7 @@
 {
 	uintptr_t hpipe_addr, comphy_addr, addr;
 	uint32_t mask, data;
+	uint8_t ap_nr, cp_nr, phy_polarity_invert;
 	int ret = 0;
 
 	debug_enter();
@@ -1930,6 +1931,13 @@
 	mvebu_cp110_comphy_set_pipe_selector(comphy_base, comphy_index,
 					     comphy_mode);
 
+	mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+
+	const struct usb_params *usb_static_values =
+			&usb_static_values_tab[ap_nr][cp_nr][comphy_index];
+
+	phy_polarity_invert = usb_static_values->polarity_invert;
+
 	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
 				comphy_index);
 	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
@@ -2009,6 +2017,13 @@
 		0x1 << HPIPE_TST_MODE_CTRL_MODE_MARGIN_OFFSET,
 		HPIPE_TST_MODE_CTRL_MODE_MARGIN_MASK);
 
+	/* The polarity inversion for USB was not tested due to lack of hw
+	 * design which requires it. Support is added for customer needs.
+	 */
+	if (phy_polarity_invert)
+		mvebu_cp110_polarity_invert(hpipe_addr + HPIPE_SYNC_PATTERN_REG,
+					    phy_polarity_invert);
+
 	/* Start analog parameters from ETP(HW) */
 	debug("stage: Analog parameters from ETP(HW)\n");
 	/* Set Pin DFE_PAT_DIS -> Bit[1]: PIN_DFE_PAT_DIS = 0x0 */
diff --git a/drivers/marvell/comphy/phy-comphy-cp110.h b/drivers/marvell/comphy/phy-comphy-cp110.h
index 1dc3aa2..b4a2102 100644
--- a/drivers/marvell/comphy/phy-comphy-cp110.h
+++ b/drivers/marvell/comphy/phy-comphy-cp110.h
@@ -81,6 +81,10 @@
 	_Bool valid;
 };
 
+struct usb_params {
+	uint8_t polarity_invert;
+};
+
 int mvebu_cp110_comphy_is_pll_locked(uint64_t comphy_base,
 				     uint8_t comphy_index);
 int mvebu_cp110_comphy_power_off(uint64_t comphy_base,
diff --git a/drivers/marvell/comphy/phy-default-porting-layer.h b/drivers/marvell/comphy/phy-default-porting-layer.h
index 28bfcf2..3c63c64 100644
--- a/drivers/marvell/comphy/phy-default-porting-layer.h
+++ b/drivers/marvell/comphy/phy-default-porting-layer.h
@@ -49,4 +49,11 @@
 		.valid = 0x1
 	},
 };
+
+static const struct usb_params
+	usb_static_values_tab[AP_NUM][CP_NUM][MAX_LANE_NR] = {
+	[0 ... AP_NUM-1][0 ... CP_NUM-1][0 ... MAX_LANE_NR-1] = {
+		.polarity_invert = COMPHY_POLARITY_NO_INVERT
+	},
+};
 #endif /* PHY_DEFAULT_PORTING_LAYER_H */