diff --git a/drivers/nxp/console/16550_console.S b/drivers/nxp/console/16550_console.S
new file mode 100644
index 0000000..044d3d0
--- /dev/null
+++ b/drivers/nxp/console/16550_console.S
@@ -0,0 +1,319 @@
+/*
+ * Copyright (c) 2021, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <arch.h>
+#include <asm_macros.S>
+#include <assert_macros.S>
+#include <console_macros.S>
+
+/* UART16550 Registers */
+#define UARTTX			0x0
+#define UARTRX			0x0
+#define UARTDLL			0x0
+#define UARTIER			0x1
+#define UARTDLLM		0x1
+#define UARTFCR			0x2
+#define UARTLCR			0x3
+#define UARTLSR			0x5
+#define UARTMCR                 0x4
+
+/* FIFO Control Register bits */
+#define UARTFCR_FIFOMD_16450	(0 << 6)
+#define UARTFCR_FIFOMD_16550	(1 << 6)
+#define UARTFCR_RXTRIG_1	(0 << 6)
+#define UARTFCR_RXTRIG_4	(1 << 6)
+#define UARTFCR_RXTRIG_8	(2 << 6)
+#define UARTFCR_RXTRIG_16	(3 << 6)
+#define UARTFCR_TXTRIG_1	(0 << 4)
+#define UARTFCR_TXTRIG_4	(1 << 4)
+#define UARTFCR_TXTRIG_8	(2 << 4)
+#define UARTFCR_TXTRIG_16	(3 << 4)
+#define UARTFCR_DMAEN		(1 << 3)	/* Enable DMA mode */
+#define UARTFCR_TXCLR		(1 << 2)	/* Clear contents of Tx FIFO */
+#define UARTFCR_RXCLR		(1 << 1)	/* Clear contents of Rx FIFO */
+#define UARTFCR_FIFOEN		(1 << 0)	/* Enable the Tx/Rx FIFO */
+#define UARTFCR_64FIFO          (1 << 5)
+
+/* Line Control Register bits */
+#define UARTLCR_DLAB		(1 << 7)	/* Divisor Latch Access */
+#define UARTLCR_SETB		(1 << 6)	/* Set BREAK Condition */
+#define UARTLCR_SETP		(1 << 5)	/* Set Parity to LCR[4] */
+#define UARTLCR_EVEN		(1 << 4)	/* Even Parity Format */
+#define UARTLCR_PAR		(1 << 3)	/* Parity */
+#define UARTLCR_STOP		(1 << 2)	/* Stop Bit */
+#define UARTLCR_WORDSZ_5	0		/* Word Length of 5 */
+#define UARTLCR_WORDSZ_6	1		/* Word Length of 6 */
+#define UARTLCR_WORDSZ_7	2		/* Word Length of 7 */
+#define UARTLCR_WORDSZ_8	3		/* Word Length of 8 */
+
+/* Line Status Register bits */
+#define UARTLSR_RXFIFOEMT	(1 << 9)	/* Rx Fifo Empty */
+#define UARTLSR_TXFIFOFULL	(1 << 8)	/* Tx Fifo Full */
+#define UARTLSR_RXFIFOERR	(1 << 7)	/* Rx Fifo Error */
+#define UARTLSR_TEMT		(1 << 6)	/* Tx Shift Register Empty */
+#define UARTLSR_THRE		(1 << 5)	/* Tx Holding Register Empty */
+#define UARTLSR_BRK		(1 << 4)	/* Break Condition Detected */
+#define UARTLSR_FERR		(1 << 3)	/* Framing Error */
+#define UARTLSR_PERR		(1 << 3)	/* Parity Error */
+#define UARTLSR_OVRF		(1 << 2)	/* Rx Overrun Error */
+#define UARTLSR_RDR		(1 << 2)	/* Rx Data Ready */
+
+#define CONSOLE_T_16550_BASE	CONSOLE_T_BASE
+
+	/*
+	 * "core" functions are low-level implementations that don't require
+	 * writable memory and are thus safe to call in BL1 crash context.
+	 */
+	.globl nxp_console_16550_core_init
+	.globl nxp_console_16550_core_putc
+	.globl nxp_console_16550_core_getc
+	.globl nxp_console_16550_core_flush
+
+	.globl console_16550_putc
+	.globl console_16550_getc
+	.globl console_16550_flush
+
+	/* -----------------------------------------------
+	 * int nxp_console_16550_core_init(uintptr_t base_addr,
+	 * unsigned int uart_clk, unsigned int baud_rate)
+	 * Function to initialize the console without a
+	 * C Runtime to print debug information. This
+	 * function will be accessed by console_init and
+	 * crash reporting.
+	 * In: x0 - console base address
+	 *     w1 - Uart clock in Hz
+	 *     w2 - Baud rate
+	 * Out: return 1 on success, 0 on error
+	 * Clobber list : x1, x2, x3
+	 * -----------------------------------------------
+	 */
+func nxp_console_16550_core_init
+	/* Check the input base address */
+	cbz	x0, init_fail
+	/* Check baud rate and uart clock for sanity */
+	cbz	w1, init_fail
+	cbz	w2, init_fail
+
+	/* Program the baudrate */
+	/* Divisor =  Uart clock / (16 * baudrate) */
+	lsl	w2, w2, #4
+	udiv	w2, w1, w2
+	and	w1, w2, #0xff		/* w1 = DLL */
+	lsr	w2, w2, #8
+	and	w2, w2, #0xff		/* w2 = DLLM */
+	ldrb	w3, [x0, #UARTLCR]
+	orr	w3, w3, #UARTLCR_DLAB
+	strb	w3, [x0, #UARTLCR]	/* enable DLL, DLLM programming */
+	strb	w1, [x0, #UARTDLL]	/* program DLL */
+	strb	w2, [x0, #UARTDLLM]	/* program DLLM */
+	mov	w2, #~UARTLCR_DLAB
+	and	w3, w3, w2
+	strb	w3, [x0, #UARTLCR]	/* disable DLL, DLLM programming */
+
+	/* 8n1 */
+	mov	w3, #3
+	strb	w3, [x0, #UARTLCR]
+	/* no interrupt */
+	mov	w3, #0
+	strb	w3, [x0, #UARTIER]
+	/* enable fifo, DMA */
+	mov	w3, #(UARTFCR_FIFOEN |UARTFCR_TXCLR | UARTFCR_RXCLR)
+	strb	w3, [x0, #UARTFCR]
+	/* DTR + RTS */
+	mov	w3, #3
+	str	w3, [x0, #UARTMCR]
+	mov	w0, #1
+	ret
+init_fail:
+	mov	w0, #0
+	ret
+endfunc nxp_console_16550_core_init
+
+	.globl nxp_console_16550_register
+
+	/* -----------------------------------------------
+	 * int nxp_console_16550_register(uintptr_t baseaddr,
+	 *     uint32_t clock, uint32_t baud,
+	 *     console_t *console);
+	 * Function to initialize and register a new 16550
+	 * console. Storage passed in for the console struct
+	 * *must* be persistent (i.e. not from the stack).
+	 * If w1 (UART clock) is 0, initialisation will be
+	 * skipped, relying on previous code to have done
+	 * this already. w2 is ignored then as well.
+	 * In: x0 - UART register base address
+	 *     w1 - UART clock in Hz
+	 *     w2 - Baud rate (ignored if w1 is 0)
+	 *     x3 - pointer to empty console_t struct
+	 * Out: return 1 on success, 0 on error
+	 * Clobber list : x0, x1, x2, x6, x7, x14
+	 * -----------------------------------------------
+	 */
+func nxp_console_16550_register
+	mov	x7, x30
+	mov	x6, x3
+	cbz	x6, register_fail
+	str	x0, [x6, #CONSOLE_T_16550_BASE]
+
+	/* A clock rate of zero means to skip the initialisation. */
+	cbz	w1, register_16550
+
+	bl	nxp_console_16550_core_init
+	cbz	x0, register_fail
+
+register_16550:
+	mov	x0, x6
+	mov	x30, x7
+	finish_console_register 16550 putc=1, getc=1, flush=1
+
+register_fail:
+	ret	x7
+endfunc nxp_console_16550_register
+
+	/* --------------------------------------------------------
+	 * int console_16550_core_putc(int c, uintptr_t base_addr)
+	 * Function to output a character over the console. It
+	 * returns the character printed on success or -1 on error.
+	 * In : w0 - character to be printed
+	 *      x1 - console base address
+	 * Out : return -1 on error else return character.
+	 * Clobber list : x2
+	 * --------------------------------------------------------
+	 */
+func nxp_console_16550_core_putc
+#if ENABLE_ASSERTIONS
+	cmp	x1, #0
+	ASM_ASSERT(ne)
+#endif /* ENABLE_ASSERTIONS */
+
+	/* Prepend '\r' to '\n' */
+	cmp	w0, #'\n'
+	b.ne	2f
+	/* Check if the transmit FIFO is full */
+1:	ldrb	w2, [x1, #UARTLSR]
+	and	w2, w2, #UARTLSR_THRE        /* #(UARTLSR_TEMT | UARTLSR_THRE)*/
+	cmp	w2, #(UARTLSR_THRE)
+	b.ne	1b
+	mov	w2, #'\r'
+	strb	w2, [x1, #UARTTX]
+	ldrb	w2, [x1, #UARTFCR]
+	orr	w2, w2, #UARTFCR_TXCLR
+
+	/* Check if the transmit FIFO is full */
+2:	ldrb	w2, [x1, #UARTLSR]
+	and	w2, w2, #(UARTLSR_THRE)
+	cmp	w2, #(UARTLSR_THRE)
+	b.ne	2b
+	strb	w0, [x1, #UARTTX]
+	ret
+endfunc nxp_console_16550_core_putc
+
+	/* --------------------------------------------------------
+	 * int console_16550_putc(int c, console_t *console)
+	 * Function to output a character over the console. It
+	 * returns the character printed on success or -1 on error.
+	 * In : w0 - character to be printed
+	 *      x1 - pointer to console_t structure
+	 * Out : return -1 on error else return character.
+	 * Clobber list : x2
+	 * --------------------------------------------------------
+	 */
+func console_16550_putc
+#if ENABLE_ASSERTIONS
+	cmp	x1, #0
+	ASM_ASSERT(ne)
+#endif /* ENABLE_ASSERTIONS */
+	ldr	x1, [x1, #CONSOLE_T_16550_BASE]
+	b	nxp_console_16550_core_putc
+endfunc console_16550_putc
+
+	/* ---------------------------------------------
+	 * int console_16550_core_getc(uintptr_t base_addr)
+	 * Function to get a character from the console.
+	 * It returns the character grabbed on success
+	 * or -1 on if no character is available.
+	 * In :  x0 - console base address
+	 * Out : w0 - character if available, else -1
+	 * Clobber list : x0, x1
+	 * ---------------------------------------------
+	 */
+func nxp_console_16550_core_getc
+#if ENABLE_ASSERTIONS
+	cmp	x0, #0
+	ASM_ASSERT(ne)
+#endif /* ENABLE_ASSERTIONS */
+
+	/* Check if the receive FIFO is empty */
+1:	ldrb	w1, [x0, #UARTLSR]
+	tbz	w1, #UARTLSR_RDR, 1b
+	ldrb	w0, [x0, #UARTRX]
+	ret
+no_char:
+	mov	w0, #ERROR_NO_PENDING_CHAR
+	ret
+endfunc nxp_console_16550_core_getc
+
+	/* ---------------------------------------------
+	 * int console_16550_getc(console_t *console)
+	 * Function to get a character from the console.
+	 * It returns the character grabbed on success
+	 * or -1 on if no character is available.
+	 * In :  x0 - pointer to console_t structure
+	 * Out : w0 - character if available, else -1
+	 * Clobber list : x0, x1
+	 * ---------------------------------------------
+	 */
+func console_16550_getc
+#if ENABLE_ASSERTIONS
+	cmp	x1, #0
+	ASM_ASSERT(ne)
+#endif /* ENABLE_ASSERTIONS */
+	ldr	x0, [x0, #CONSOLE_T_16550_BASE]
+	b	nxp_console_16550_core_getc
+endfunc console_16550_getc
+
+	/* ---------------------------------------------
+	 * int console_16550_core_flush(uintptr_t base_addr)
+	 * Function to force a write of all buffered
+	 * data that hasn't been output.
+	 * In : x0 - console base address
+	 * Out : return -1 on error else return 0.
+	 * Clobber list : x0, x1
+	 * ---------------------------------------------
+	 */
+func nxp_console_16550_core_flush
+#if ENABLE_ASSERTIONS
+	cmp	x0, #0
+	ASM_ASSERT(ne)
+#endif /* ENABLE_ASSERTIONS */
+
+	/* Loop until the transmit FIFO is empty */
+1:	ldrb	w1, [x0, #UARTLSR]
+	and	w1, w1, #(UARTLSR_THRE)
+	cmp	w1, #(UARTLSR_THRE)
+	b.ne	1b
+
+	mov	w0, #0
+	ret
+endfunc nxp_console_16550_core_flush
+
+	/* ---------------------------------------------
+	 * int console_16550_flush(console_t *console)
+	 * Function to force a write of all buffered
+	 * data that hasn't been output.
+	 * In : x0 - pointer to console_t structure
+	 * Out : return -1 on error else return 0.
+	 * Clobber list : x0, x1
+	 * ---------------------------------------------
+	 */
+func console_16550_flush
+#if ENABLE_ASSERTIONS
+	cmp	x0, #0
+	ASM_ASSERT(ne)
+#endif /* ENABLE_ASSERTIONS */
+	ldr	x0, [x0, #CONSOLE_T_16550_BASE]
+	b	nxp_console_16550_core_flush
+endfunc console_16550_flush
diff --git a/drivers/nxp/console/console.mk b/drivers/nxp/console/console.mk
new file mode 100644
index 0000000..22d1336
--- /dev/null
+++ b/drivers/nxp/console/console.mk
@@ -0,0 +1,46 @@
+#
+# Copyright 2021 NXP
+#
+# SPDX-License-Identifier: BSD-3-Clause
+#
+#
+#------------------------------------------------------------------------------
+#
+# Select the CORE files
+#
+# -----------------------------------------------------------------------------
+
+ifeq (${ADD_CONSOLE},)
+
+ADD_CONSOLE		:= 1
+
+PLAT_INCLUDES		+=	-I$(PLAT_DRIVERS_PATH)/console
+
+ifeq ($(CONSOLE), NS16550)
+NXP_CONSOLE		:=	NS16550
+
+$(eval $(call add_define_val,NXP_CONSOLE,${NXP_CONSOLE}))
+
+CONSOLE_SOURCES		:=	$(PLAT_DRIVERS_PATH)/console/16550_console.S	\
+				$(PLAT_DRIVERS_PATH)/console/console_16550.c
+else
+ifeq ($(CONSOLE), PL011)
+CONSOLE_SOURCES		:=	drivers/arm/pl011/aarch64/pl011_console.S	\
+				${PLAT_DRIVERS_PATH}/console/console_pl011.c
+else
+	$(error -> CONSOLE not set!)
+endif
+endif
+
+ifeq (${BL_COMM_CONSOLE_NEEDED},yes)
+BL_COMMON_SOURCES	+= ${CONSOLE_SOURCES}
+else
+ifeq (${BL2_CONSOLE_NEEDED},yes)
+BL2_SOURCES		+= ${CONSOLE_SOURCES}
+endif
+ifeq (${BL31_CONSOLE_NEEDED},yes)
+BL31_SOURCES		+= ${CONSOLE_SOURCES}
+endif
+endif
+endif
+# -----------------------------------------------------------------------------
diff --git a/drivers/nxp/console/console_16550.c b/drivers/nxp/console/console_16550.c
new file mode 100644
index 0000000..fa5c5bb
--- /dev/null
+++ b/drivers/nxp/console/console_16550.c
@@ -0,0 +1,33 @@
+/*
+ * Copyright 2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+#include <assert.h>
+
+#include <common/debug.h>
+#include <dcfg.h>
+#include <lib/utils.h>
+#include <plat_console.h>
+
+/*
+ * Perform Arm specific early platform setup. At this moment we only initialize
+ * the console and the memory layout.
+ */
+void plat_console_init(uintptr_t nxp_console_addr, uint32_t uart_clk_div,
+			uint32_t baud)
+{
+	struct sysinfo sys;
+	static console_t nxp_console;
+
+	zeromem(&sys, sizeof(sys));
+	if (get_clocks(&sys)) {
+		ERROR("System clocks are not set\n");
+		panic();
+	}
+	nxp_console_16550_register(nxp_console_addr,
+			      (sys.freq_platform/uart_clk_div),
+			       baud, &nxp_console);
+}
diff --git a/drivers/nxp/console/console_pl011.c b/drivers/nxp/console/console_pl011.c
new file mode 100644
index 0000000..93f2fc2
--- /dev/null
+++ b/drivers/nxp/console/console_pl011.c
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+#include <assert.h>
+
+#include <common/debug.h>
+#include <dcfg.h>
+#include <drivers/arm/pl011.h>
+#include <drivers/console.h>
+#include <lib/utils.h>
+
+/*
+ * Perform Arm specific early platform setup. At this moment we only initialize
+ * the console and the memory layout.
+ */
+void plat_console_init(uintptr_t nxp_console_addr, uint32_t uart_clk_div,
+			uint32_t baud)
+{
+	struct sysinfo sys;
+	static console_t nxp_console;
+
+	zeromem(&sys, sizeof(sys));
+	if (get_clocks(&sys)) {
+		ERROR("System clocks are not set\n");
+		panic();
+	}
+
+	console_pl011_register(nxp_console_addr,
+			      (sys.freq_platform/uart_clk_div),
+			       baud, &nxp_console);
+}
diff --git a/drivers/nxp/console/plat_console.h b/drivers/nxp/console/plat_console.h
new file mode 100644
index 0000000..8b1b23a
--- /dev/null
+++ b/drivers/nxp/console/plat_console.h
@@ -0,0 +1,38 @@
+/*
+ * Copyright 2021 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+#ifndef PLAT_CONSOLE_H
+#define PLAT_CONSOLE_H
+
+#include <stdint.h>
+#include <drivers/console.h>
+
+#if (NXP_CONSOLE == NS16550)
+/*
+ * NXP specific UART - 16550 configuration
+ *
+ * Initialize a NXP 16550 console instance and register it with the console
+ * framework. The |console| pointer must point to storage that will be valid
+ * for the lifetime of the console, such as a global or static local variable.
+ * Its contents will be reinitialized from scratch.
+ * When |clock| has a value of 0, the UART will *not* be initialised. This
+ * means the UART should already be enabled and the baudrate and clock setup
+ * should have been done already, either by platform specific code or by
+ * previous firmware stages. The |baud| parameter will be ignored in this
+ * case as well.
+ */
+int nxp_console_16550_register(uintptr_t baseaddr, uint32_t clock,
+			       uint32_t baud, console_t *console);
+#endif
+/*
+ * Function to initialize platform's console
+ * and register with console framework
+ */
+void plat_console_init(uintptr_t nxp_console_addr, uint32_t uart_clk_div,
+			uint32_t baud);
+
+#endif