plat: marvell: armada: a8k: Add support for iEi Puzzle-M801 board
Add support for the iEi Puzzle-M801 board that is based on
the Marvell Armada 88F8040 SoC.
It supports 1 x 288-pin DIMM, DDR4 2400MHz up to 16 GB (ECC).
The iEi Puzzle-M801 board is using a custom MCU to handle board
power management. The MCU is managing the boards power LEDs, fans
and some other periferals. It's using UART for communication.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Change-Id: I0826ef8bf651b69aad5803184f20930ac7212ef8
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/board/dram_port.c b/plat/marvell/armada/a8k/a80x0_puzzle/board/dram_port.c
new file mode 100644
index 0000000..46a9a26
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/board/dram_port.c
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <common/debug.h>
+#include <drivers/mentor/mi2cv.h>
+#include <lib/mmio.h>
+
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_AP_MPP_CTRL0_7_REG MVEBU_AP_MPP_REGS(0)
+#define MVEBU_AP_MPP_CTRL4_OFFS 16
+#define MVEBU_AP_MPP_CTRL5_OFFS 20
+#define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA 0x3
+#define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA 0x3
+
+#define MVEBU_CP_MPP_CTRL37_OFFS 20
+#define MVEBU_CP_MPP_CTRL38_OFFS 24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA 0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA 0x2
+
+#define MVEBU_MPP_CTRL_MASK 0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+ /* Board with 1CS 8Gb x4 devices of Micron 2400T */
+ DEBUG_LEVEL_ERROR,
+ 0x1, /* active interfaces */
+ /* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+ { { { {0x1, 0x0, 0, 0}, /* FIXME: change the cs mask for all 64 bit */
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0},
+ {0x1, 0x0, 0, 0} },
+ /* TODO: double check if the speed bin is 2400T */
+ SPEED_BIN_DDR_2400T, /* speed_bin */
+ MV_DDR_DEV_WIDTH_8BIT, /* sdram device width */
+ MV_DDR_DIE_CAP_8GBIT, /* die capacity */
+ MV_DDR_FREQ_SAR, /* frequency */
+ 0, 0, /* cas_l, cas_wl */
+ MV_DDR_TEMP_LOW} }, /* temperature */
+ MV_DDR_64BIT_BUS_MASK, /* subphys mask */
+ MV_DDR_CFG_SPD, /* ddr configuration data source */
+ { {0} }, /* raw spd data */
+ {0}, /* timing parameters */
+ { /* electrical configuration */
+ { /* memory electrical configuration */
+ MV_DDR_RTT_NOM_PARK_RZQ_DISABLE, /* rtt_nom */
+ {
+ MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+ MV_DDR_RTT_NOM_PARK_RZQ_DIV1 /* rtt_park 2cs */
+ },
+ {
+ MV_DDR_RTT_WR_DYN_ODT_OFF, /* rtt_wr 1cs */
+ MV_DDR_RTT_WR_RZQ_DIV2 /* rtt_wr 2cs */
+ },
+ MV_DDR_DIC_RZQ_DIV7 /* dic */
+ },
+ { /* phy electrical configuration */
+ MV_DDR_OHM_30, /* data_drv_p */
+ MV_DDR_OHM_30, /* data_drv_n */
+ MV_DDR_OHM_30, /* ctrl_drv_p */
+ MV_DDR_OHM_30, /* ctrl_drv_n */
+ {
+ MV_DDR_OHM_60, /* odt_p 1cs */
+ MV_DDR_OHM_120 /* odt_p 2cs */
+ },
+ {
+ MV_DDR_OHM_60, /* odt_n 1cs */
+ MV_DDR_OHM_120 /* odt_n 2cs */
+ },
+ },
+ { /* mac electrical configuration */
+ MV_DDR_ODT_CFG_NORMAL, /* odtcfg_pattern */
+ MV_DDR_ODT_CFG_ALWAYS_ON, /* odtcfg_write */
+ MV_DDR_ODT_CFG_NORMAL, /* odtcfg_read */
+ },
+ }
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+ /* Return the board topology as defined in the board code */
+ return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+ uint32_t val;
+ uintptr_t reg;
+
+ /* configure ap mmps 4, 5 to I2C */
+ reg = MVEBU_AP_MPP_CTRL0_7_REG;
+
+ val = mmio_read_32(reg);
+ val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_AP_MPP_CTRL4_OFFS) |
+ (MVEBU_MPP_CTRL_MASK << MVEBU_AP_MPP_CTRL5_OFFS));
+ val |= ((MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA << MVEBU_AP_MPP_CTRL4_OFFS) |
+ (MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA << MVEBU_AP_MPP_CTRL5_OFFS));
+
+ mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+ struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+ INFO("Gathering DRAM information\n");
+
+ if (tm->cfg_src == MV_DDR_CFG_SPD) {
+ /* configure MPPs to enable i2c */
+ mpp_config();
+ /* initialize the MVEBU_AP_I2C_BASE I2C bus */
+ i2c_init((void *)MVEBU_AP_I2C_BASE);
+ /* select SPD memory page 0 to access DRAM configuration */
+ i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1);
+ /* read data from spd */
+ i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+ sizeof(tm->spd_data.all_bytes));
+ }
+}
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/board/marvell_plat_config.c b/plat/marvell/armada/a8k/a80x0_puzzle/board/marvell_plat_config.c
new file mode 100644
index 0000000..0edc977
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/board/marvell_plat_config.c
@@ -0,0 +1,201 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <drivers/delay_timer.h>
+#include <lib/mmio.h>
+
+#include <armada_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * GPIO Configuration
+ *****************************************************************************
+ */
+#define MPP_CONTROL_REGISTER 0xf2440018
+#define MPP_CONTROL_MPP_SEL_52_MASK 0xf0000
+#define GPIO_DATA_OUT1_REGISTER 0xf2440140
+#define GPIO_DATA_OUT_EN_CTRL1_REGISTER 0xf2440144
+#define GPIO52_MASK 0x100000
+
+/* Reset PCIe via GPIO number 52 */
+int marvell_gpio_config(void)
+{
+ uint32_t reg;
+
+ reg = mmio_read_32(MPP_CONTROL_REGISTER);
+ reg |= MPP_CONTROL_MPP_SEL_52_MASK;
+ mmio_write_32(MPP_CONTROL_REGISTER, reg);
+
+ reg = mmio_read_32(GPIO_DATA_OUT1_REGISTER);
+ reg |= GPIO52_MASK;
+ mmio_write_32(GPIO_DATA_OUT1_REGISTER, reg);
+
+ reg = mmio_read_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER);
+ reg &= ~GPIO52_MASK;
+ mmio_write_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER, reg);
+ udelay(100);
+
+ return 0;
+}
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+ /* CP1 SPI1 CS0 Direct Mode access */
+ {0xf900, 0x1000000, AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+ uintptr_t base)
+{
+ *win = amb_memory_map;
+ if (*win == NULL)
+ *size = 0;
+ else
+ *size = ARRAY_SIZE(amb_memory_map);
+
+ return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+ /* CP1 (MCI0) internal regs */
+ {0x00000000f4000000, 0x2000000, MCI_0_TID},
+#ifndef IMAGE_BLE
+ /* PCIe0 and SPI1_CS0 (RUNIT) on CP1*/
+ {0x00000000f9000000, 0x2000000, MCI_0_TID},
+ /* PCIe1 on CP1*/
+ {0x00000000fb000000, 0x1000000, MCI_0_TID},
+ /* PCIe2 on CP1*/
+ {0x00000000fc000000, 0x1000000, MCI_0_TID},
+ /* MCI 0 indirect window */
+ {MVEBU_MCI_REG_BASE_REMAP(0), 0x100000, MCI_0_TID},
+ /* MCI 1 indirect window */
+ {MVEBU_MCI_REG_BASE_REMAP(1), 0x100000, MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+ return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+ uint32_t *size)
+{
+ *win = io_win_memory_map;
+ if (*win == NULL)
+ *size = 0;
+ else
+ *size = ARRAY_SIZE(io_win_memory_map);
+
+ return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map_cp0[] = {
+ /* CP0 */
+ /* PEX1_X1 window */
+ {0x00000000f7000000, 0x1000000, PEX1_TID},
+ /* PEX2_X1 window */
+ {0x00000000f8000000, 0x1000000, PEX2_TID},
+ /* PEX0_X4 window */
+ {0x00000000f6000000, 0x1000000, PEX0_TID},
+ {0x00000000c0000000, 0x30000000, PEX0_TID},
+ {0x0000000800000000, 0x100000000, PEX0_TID},
+};
+
+struct addr_map_win iob_memory_map_cp1[] = {
+ /* CP1 */
+ /* SPI1_CS0 (RUNIT) window */
+ {0x00000000f9000000, 0x1000000, RUNIT_TID},
+ /* PEX1_X1 window */
+ {0x00000000fb000000, 0x1000000, PEX1_TID},
+ /* PEX2_X1 window */
+ {0x00000000fc000000, 0x1000000, PEX2_TID},
+ /* PEX0_X4 window */
+ {0x00000000fa000000, 0x1000000, PEX0_TID}
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+ uintptr_t base)
+{
+ switch (base) {
+ case MVEBU_CP_REGS_BASE(0):
+ *win = iob_memory_map_cp0;
+ *size = ARRAY_SIZE(iob_memory_map_cp0);
+ return 0;
+ case MVEBU_CP_REGS_BASE(1):
+ *win = iob_memory_map_cp1;
+ *size = ARRAY_SIZE(iob_memory_map_cp1);
+ return 0;
+ default:
+ *size = 0;
+ *win = 0;
+ return 1;
+ }
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+ {0x00000000f2000000, 0x4000000, IO_0_TID}, /* IO window */
+#else
+#if LLC_SRAM
+ {PLAT_MARVELL_LLC_SRAM_BASE, PLAT_MARVELL_LLC_SRAM_SIZE, SRAM_TID},
+#endif
+ {0x00000000f2000000, 0xe000000, IO_0_TID}, /* IO window */
+ {0x00000000c0000000, 0x30000000, IO_0_TID}, /* IO window */
+ {0x0000000800000000, 0x100000000, IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+ return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+ uint32_t *size)
+{
+ *win = ccu_memory_map;
+ *size = ARRAY_SIZE(ccu_memory_map);
+
+ return 0;
+}
+
+/* In reference to #ifndef IMAGE_BLE, this part is used for BLE only. */
+
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+void *plat_marvell_get_skip_image_data(void)
+{
+ /* No recovery button on A8k-MCBIN board */
+ return NULL;
+}
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/board/system_power.c b/plat/marvell/armada/a8k/a80x0_puzzle/board/system_power.c
new file mode 100644
index 0000000..5147dd5
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/board/system_power.c
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2020 Sartura Ltd.
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <armada_common.h>
+#include <common/debug.h>
+#include <drivers/delay_timer.h>
+#include <drivers/ti/uart/uart_16550.h>
+#include <drivers/console.h>
+#include <plat_marvell.h>
+
+/*****************************************************************************
+ * Platform specific power off functions
+ * Power off PSU / Send command to power management MCU / ...
+ *****************************************************************************
+ */
+
+unsigned char add_xor_checksum(unsigned char *buf, unsigned char xor_len)
+{
+ unsigned char xor_sum = 0;
+ unsigned int i;
+
+ for (i = 0; i < xor_len; i++)
+ xor_sum ^= buf[i];
+
+ return xor_sum;
+}
+
+int system_power_off(void)
+{
+ static console_t console;
+
+ /* WT61P803 MCU system_off_now command */
+ unsigned char system_off_now[4] = { '@', 'C', '0' };
+ int i, len;
+
+ len = sizeof(system_off_now);
+ system_off_now[len - 1] = add_xor_checksum(system_off_now, len);
+
+ console_16550_register(PLAT_MARVELL_BOOT_UART_BASE + 0x100,
+ PLAT_MARVELL_BOOT_UART_CLK_IN_HZ, 115200, &console);
+
+ /* Send system_off_now to console */
+ for (i = 0; i < len; i++) {
+ console.putc(system_off_now[i], &console);
+ udelay(1000);
+ }
+
+ console.flush(&console);
+ (void)console_unregister(&console);
+
+ mdelay(100);
+
+ return 0;
+}
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/mvebu_def.h b/plat/marvell/armada/a8k/a80x0_puzzle/mvebu_def.h
new file mode 100644
index 0000000..3fa119a
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/mvebu_def.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef MVEBU_DEF_H
+#define MVEBU_DEF_H
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT 2 /* A80x0 has both CP0 & CP1 */
+#define I2C_SPD_ADDR 0x53 /* Access SPD data */
+#define I2C_SPD_P0_ADDR 0x36 /* Select SPD data page 0 */
+
+#endif /* MVEBU_DEF_H */
diff --git a/plat/marvell/armada/a8k/a80x0_puzzle/platform.mk b/plat/marvell/armada/a8k/a80x0_puzzle/platform.mk
new file mode 100644
index 0000000..3378d53
--- /dev/null
+++ b/plat/marvell/armada/a8k/a80x0_puzzle/platform.mk
@@ -0,0 +1,20 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier: BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT := 0
+
+CP_NUM := 2
+$(eval $(call add_define,CP_NUM))
+
+DOIMAGE_SEC := tools/doimage/secure/sec_img_8K.cfg
+
+MARVELL_MOCHI_DRV := drivers/marvell/mochi/apn806_setup.c
+
+BOARD_DIR := $(shell dirname $(lastword $(MAKEFILE_LIST)))
+include plat/marvell/armada/a8k/common/a8k_common.mk
+
+include plat/marvell/armada/common/marvell_common.mk