diff --git a/plat/marvell/a8k/a70x0/board/dram_port.c b/plat/marvell/a8k/a70x0/board/dram_port.c
new file mode 100644
index 0000000..c670258
--- /dev/null
+++ b/plat/marvell/a8k/a70x0/board/dram_port.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <debug.h>
+#include <mv_ddr_if.h>
+#include <plat_marvell.h>
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+}
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+/* FIXME: MISL board 2CS 4Gb x8 devices of micron - 2133P */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2133P,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_4GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	MV_DDR_32BIT_ECC_PUP8_BUS_MASK,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
diff --git a/plat/marvell/a8k/a70x0/board/marvell_plat_config.c b/plat/marvell/a8k/a70x0/board/marvell_plat_config.c
new file mode 100644
index 0000000..9171986
--- /dev/null
+++ b/plat/marvell/a8k/a70x0/board/marvell_plat_config.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <a8k_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP0 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win,
+			       uint32_t *size, uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO_WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+#ifndef IMAGE_BLE
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000, MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000, MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map[] = {
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = iob_memory_map;
+	*size = ARRAY_SIZE(iob_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {	/* IO window */
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,	IO_0_TID}, /* IO window */
+#else
+	{0x00000000f2000000,	0xe000000,	IO_0_TID},
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifdef IMAGE_BLE
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+struct skip_image skip_im = {
+	.detection_method = GPIO,
+	.info.gpio.num = 33,
+	.info.gpio.button_state = HIGH,
+	.info.test.cp_ap = CP,
+	.info.test.cp_index = 0,
+};
+
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* Return the skip_image configurations */
+	return &skip_im;
+}
+#endif
+#endif
diff --git a/plat/marvell/a8k/a70x0/mvebu_def.h b/plat/marvell/a8k/a70x0/mvebu_def.h
new file mode 100644
index 0000000..a7c5abb
--- /dev/null
+++ b/plat/marvell/a8k/a70x0/mvebu_def.h
@@ -0,0 +1,15 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef __MVEBU_DEF_H__
+#define __MVEBU_DEF_H__
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		1	/* A70x0 has single CP0 */
+
+#endif /* __MVEBU_DEF_H__ */
diff --git a/plat/marvell/a8k/a70x0/platform.mk b/plat/marvell/a8k/a70x0/platform.mk
new file mode 100644
index 0000000..29dfd95
--- /dev/null
+++ b/plat/marvell/a8k/a70x0/platform.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_7K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+include plat/marvell/a8k/common/a8k_common.mk
+
+include plat/marvell/common/marvell_common.mk
diff --git a/plat/marvell/a8k/a70x0_amc/board/dram_port.c b/plat/marvell/a8k/a70x0_amc/board/dram_port.c
new file mode 100644
index 0000000..ab1df46
--- /dev/null
+++ b/plat/marvell/a8k/a70x0_amc/board/dram_port.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <debug.h>
+#include <mv_ddr_if.h>
+#include <plat_marvell.h>
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+}
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+/* FIXME: MISL board 2CS 8Gb x8 devices of micron - 2133P */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0},
+	      {0x3, 0x2, 0, 0} },
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	MV_DDR_32BIT_ECC_PUP8_BUS_MASK,	/* subphys mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
diff --git a/plat/marvell/a8k/a70x0_amc/board/marvell_plat_config.c b/plat/marvell/a8k/a70x0_amc/board/marvell_plat_config.c
new file mode 100644
index 0000000..ec4124c
--- /dev/null
+++ b/plat/marvell/a8k/a70x0_amc/board/marvell_plat_config.c
@@ -0,0 +1,142 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <a8k_common.h>
+
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win *amb_memory_map;
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+#ifndef IMAGE_BLE
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,	MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,	MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map[] = {
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x6000000,	PEX0_TID},
+	{0x00000000c0000000,    0x30000000,     PEX0_TID},
+	{0x0000000800000000,    0x200000000,    PEX0_TID},
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = iob_memory_map;
+	*size = ARRAY_SIZE(iob_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,	IO_0_TID}, /* IO window */
+#else
+	{0x00000000f2000000,	0xe000000,	IO_0_TID},
+	{0x00000000c0000000,    0x30000000,	IO_0_TID}, /* IO window */
+	{0x0000000800000000,    0x200000000,	IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifdef IMAGE_BLE
+
+struct pci_hw_cfg *plat_get_pcie_hw_data(void)
+{
+	return NULL;
+}
+
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+struct skip_image skip_im = {
+	.detection_method = GPIO,
+	.info.gpio.num = 33,
+	.info.gpio.button_state = HIGH,
+	.info.test.cp_ap = CP,
+	.info.test.cp_index = 0,
+};
+
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* Return the skip_image configurations */
+	return &skip_im;
+}
+#endif
+#endif
diff --git a/plat/marvell/a8k/a70x0_amc/mvebu_def.h b/plat/marvell/a8k/a70x0_amc/mvebu_def.h
new file mode 100644
index 0000000..5c66552
--- /dev/null
+++ b/plat/marvell/a8k/a70x0_amc/mvebu_def.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef __MVEBU_DEF_H__
+#define __MVEBU_DEF_H__
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		1	/* A70x0 has single CP0 */
+
+/***********************************************************************
+ * Required platform porting definitions common to all
+ * Management Compute SubSystems (MSS)
+ ***********************************************************************
+ */
+/*
+ * Load address of SCP_BL2
+ * SCP_BL2 is loaded to the same place as BL31.
+ * Once SCP_BL2 is transferred to the SCP,
+ * it is discarded and BL31 is loaded over the top.
+ */
+#ifdef SCP_IMAGE
+#define SCP_BL2_BASE		BL31_BASE
+#endif
+
+
+#endif /* __MVEBU_DEF_H__ */
diff --git a/plat/marvell/a8k/a70x0_amc/platform.mk b/plat/marvell/a8k/a70x0_amc/platform.mk
new file mode 100644
index 0000000..29dfd95
--- /dev/null
+++ b/plat/marvell/a8k/a70x0_amc/platform.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_7K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+include plat/marvell/a8k/common/a8k_common.mk
+
+include plat/marvell/common/marvell_common.mk
diff --git a/plat/marvell/a8k/a80x0/board/dram_port.c b/plat/marvell/a8k/a80x0/board/dram_port.c
new file mode 100644
index 0000000..c720c11
--- /dev/null
+++ b/plat/marvell/a8k/a80x0/board/dram_port.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <a8k_i2c.h>
+#include <debug.h>
+#include <mmio.h>
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_AP_MPP_CTRL0_7_REG		MVEBU_AP_MPP_REGS(0)
+#define MVEBU_AP_MPP_CTRL4_OFFS			16
+#define MVEBU_AP_MPP_CTRL5_OFFS			20
+#define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA		0x3
+#define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA		0x3
+
+#define MVEBU_CP_MPP_CTRL37_OFFS		20
+#define MVEBU_CP_MPP_CTRL38_OFFS		24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA	0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA	0x2
+
+#define MVEBU_MPP_CTRL_MASK			0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	/* MISL board with 1CS 8Gb x4 devices of Micron 2400T */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x0, 0, 0},	/* FIXME: change the cs mask for all 64 bit */
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0} },
+	   /* TODO: double check if the speed bin is 2400T */
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	MV_DDR_64BIT_ECC_PUP8_BUS_MASK, /* subphys mask */
+	MV_DDR_CFG_SPD,			/* ddr configuration data source */
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+	uintptr_t reg;
+	uint32_t val;
+
+	reg = MVEBU_CP_MPP_REGS(0, 4);
+	/* configure CP0 MPP 37 and 38 to i2c */
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
+	val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA <<
+			MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA <<
+			MVEBU_CP_MPP_CTRL38_OFFS);
+	mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	INFO("Gathering DRAM information\n");
+
+	if (tm->cfg_src == MV_DDR_CFG_SPD) {
+		/* configure MPPs to enable i2c */
+		mpp_config();
+
+		/* initialize i2c */
+		i2c_init((void *)MVEBU_CP0_I2C_BASE);
+
+		/* select SPD memory page 0 to access DRAM configuration */
+		i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1);
+
+		/* read data from spd */
+		i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+			 sizeof(tm->spd_data.all_bytes));
+	}
+}
diff --git a/plat/marvell/a8k/a80x0/board/marvell_plat_config.c b/plat/marvell/a8k/a80x0/board/marvell_plat_config.c
new file mode 100644
index 0000000..43beffa
--- /dev/null
+++ b/plat/marvell/a8k/a80x0/board/marvell_plat_config.c
@@ -0,0 +1,191 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <a8k_common.h>
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP1 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+	/* CP1 (MCI0) internal regs */
+	{0x00000000f4000000,		0x2000000,  MCI_0_TID},
+#ifndef IMAGE_BLE
+	/* PCIe0 and SPI1_CS0 (RUNIT) on CP1*/
+	{0x00000000f9000000,		0x2000000,  MCI_0_TID},
+	/* PCIe1 on CP1*/
+	{0x00000000fb000000,		0x1000000,  MCI_0_TID},
+	/* PCIe2 on CP1*/
+	{0x00000000fc000000,		0x1000000,  MCI_0_TID},
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,  MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,  MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map_cp0[] = {
+	/* CP0 */
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID}
+};
+
+struct addr_map_win iob_memory_map_cp1[] = {
+	/* CP1 */
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+	/* PEX1_X1 window */
+	{0x00000000fb000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000fc000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000fa000000,	0x1000000,	PEX0_TID}
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	switch (base) {
+	case MVEBU_CP_REGS_BASE(0):
+		*win = iob_memory_map_cp0;
+		*size = ARRAY_SIZE(iob_memory_map_cp0);
+		return 0;
+	case MVEBU_CP_REGS_BASE(1):
+		*win = iob_memory_map_cp1;
+		*size = ARRAY_SIZE(iob_memory_map_cp1);
+		return 0;
+	default:
+		*size = 0;
+		*win = 0;
+		return 1;
+	}
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,  IO_0_TID}, /* IO window */
+#else
+	{0x00000000f2000000,	0xe000000,  IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * SoC PM configuration
+ *****************************************************************************
+ */
+/* CP GPIO should be used and the GPIOs should be within same GPIO register */
+struct power_off_method pm_cfg = {
+	.type = PMIC_GPIO,
+	.cfg.gpio.pin_count = 1,
+	.cfg.gpio.info = {{0, 35} },
+	.cfg.gpio.step_count = 7,
+	.cfg.gpio.seq = {1, 0, 1, 0, 1, 0, 1},
+	.cfg.gpio.delay_ms = 10,
+};
+
+void *plat_marvell_get_pm_cfg(void)
+{
+	/* Return the PM configurations */
+	return &pm_cfg;
+}
+
+/* In reference to #ifndef IMAGE_BLE, this part is used for BLE only. */
+#else
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+#if PLAT_RECOVERY_IMAGE_ENABLE
+struct skip_image skip_im = {
+	.detection_method = GPIO,
+	.info.gpio.num = 33,
+	.info.gpio.button_state = HIGH,
+	.info.test.cp_ap = CP,
+	.info.test.cp_index = 0,
+};
+
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* Return the skip_image configurations */
+	return &skip_im;
+}
+#endif
+#endif
diff --git a/plat/marvell/a8k/a80x0/mvebu_def.h b/plat/marvell/a8k/a80x0/mvebu_def.h
new file mode 100644
index 0000000..5bff12c
--- /dev/null
+++ b/plat/marvell/a8k/a80x0/mvebu_def.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef __MVEBU_DEF_H__
+#define __MVEBU_DEF_H__
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		2	/* A80x0 has both CP0 & CP1 */
+#define I2C_SPD_ADDR		0x53	/* Access SPD data */
+#define I2C_SPD_P0_ADDR		0x36	/* Select SPD data page 0 */
+
+#endif /* __MVEBU_DEF_H__ */
diff --git a/plat/marvell/a8k/a80x0/platform.mk b/plat/marvell/a8k/a80x0/platform.mk
new file mode 100644
index 0000000..0fe235b
--- /dev/null
+++ b/plat/marvell/a8k/a80x0/platform.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_8K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+include plat/marvell/a8k/common/a8k_common.mk
+
+include plat/marvell/common/marvell_common.mk
diff --git a/plat/marvell/a8k/a80x0_mcbin/board/dram_port.c b/plat/marvell/a8k/a80x0_mcbin/board/dram_port.c
new file mode 100644
index 0000000..b455b83
--- /dev/null
+++ b/plat/marvell/a8k/a80x0_mcbin/board/dram_port.c
@@ -0,0 +1,129 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <a8k_i2c.h>
+#include <debug.h>
+#include <mmio.h>
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_CP_MPP_CTRL37_OFFS		20
+#define MVEBU_CP_MPP_CTRL38_OFFS		24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA	0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA	0x2
+
+#define MVEBU_MPP_CTRL_MASK			0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	/* Board with 1CS 8Gb x4 devices of Micron 2400T */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x0, 0, 0},	/* FIXME: change the cs mask for all 64 bit */
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0} },
+	   /* TODO: double check if the speed bin is 2400T */
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	   MV_DDR_64BIT_BUS_MASK,	/* subphys mask */
+	   MV_DDR_CFG_SPD,		/* ddr configuration data source */
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+	uint32_t val;
+	uintptr_t reg = MVEBU_CP_MPP_REGS(0, 4);
+
+	/* configure CP0 MPP 37 and 38 to i2c */
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
+	val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA << MVEBU_CP_MPP_CTRL38_OFFS);
+	mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	INFO("Gathering DRAM information\n");
+
+	if (tm->cfg_src == MV_DDR_CFG_SPD) {
+		/* configure MPPs to enable i2c */
+		mpp_config();
+		/* initialize the i2c */
+		i2c_init((void *)MVEBU_CP0_I2C_BASE);
+		/* select SPD memory page 0 to access DRAM configuration */
+		i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1);
+		/* read data from spd */
+		i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+			 sizeof(tm->spd_data.all_bytes));
+	}
+}
diff --git a/plat/marvell/a8k/a80x0_mcbin/board/marvell_plat_config.c b/plat/marvell/a8k/a80x0_mcbin/board/marvell_plat_config.c
new file mode 100644
index 0000000..079bd8f
--- /dev/null
+++ b/plat/marvell/a8k/a80x0_mcbin/board/marvell_plat_config.c
@@ -0,0 +1,196 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <a8k_common.h>
+#include <delay_timer.h>
+#include <mmio.h>
+/*
+ * If bootrom is currently at BLE there's no need to include the memory
+ * maps structure at this point
+ */
+#include <mvebu_def.h>
+#ifndef IMAGE_BLE
+
+/*****************************************************************************
+ * GPIO Configuration
+ *****************************************************************************
+ */
+#define MPP_CONTROL_REGISTER		0xf2440018
+#define MPP_CONTROL_MPP_SEL_52_MASK	0xf0000
+#define GPIO_DATA_OUT1_REGISTER		0xf2440140
+#define GPIO_DATA_OUT_EN_CTRL1_REGISTER 0xf2440144
+#define GPIO52_MASK			0x100000
+
+/* Reset PCIe via GPIO number 52 */
+int marvell_gpio_config(void)
+{
+	uint32_t reg;
+
+	reg = mmio_read_32(MPP_CONTROL_REGISTER);
+	reg |= MPP_CONTROL_MPP_SEL_52_MASK;
+	mmio_write_32(MPP_CONTROL_REGISTER, reg);
+
+	reg = mmio_read_32(GPIO_DATA_OUT1_REGISTER);
+	reg |= GPIO52_MASK;
+	mmio_write_32(GPIO_DATA_OUT1_REGISTER, reg);
+
+	reg = mmio_read_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER);
+	reg &= ~GPIO52_MASK;
+	mmio_write_32(GPIO_DATA_OUT_EN_CTRL1_REGISTER, reg);
+	udelay(100);
+
+	return 0;
+}
+
+/*****************************************************************************
+ * AMB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win amb_memory_map[] = {
+	/* CP1 SPI1 CS0 Direct Mode access */
+	{0xf900,	0x1000000,	AMB_SPI1_CS0_ID},
+};
+
+int marvell_get_amb_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	*win = amb_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(amb_memory_map);
+
+	return 0;
+}
+#endif
+
+/*****************************************************************************
+ * IO WIN Configuration
+ *****************************************************************************
+ */
+struct addr_map_win io_win_memory_map[] = {
+	/* CP1 (MCI0) internal regs */
+	{0x00000000f4000000,		0x2000000,  MCI_0_TID},
+#ifndef IMAGE_BLE
+	/* PCIe0 and SPI1_CS0 (RUNIT) on CP1*/
+	{0x00000000f9000000,		0x2000000,  MCI_0_TID},
+	/* PCIe1 on CP1*/
+	{0x00000000fb000000,		0x1000000,  MCI_0_TID},
+	/* PCIe2 on CP1*/
+	{0x00000000fc000000,		0x1000000,  MCI_0_TID},
+	/* MCI 0 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(0),	0x100000,   MCI_0_TID},
+	/* MCI 1 indirect window */
+	{MVEBU_MCI_REG_BASE_REMAP(1),	0x100000,   MCI_1_TID},
+#endif
+};
+
+uint32_t marvell_get_io_win_gcr_target(int ap_index)
+{
+	return PIDI_TID;
+}
+
+int marvell_get_io_win_memory_map(int ap_index, struct addr_map_win **win,
+				  uint32_t *size)
+{
+	*win = io_win_memory_map;
+	if (*win == NULL)
+		*size = 0;
+	else
+		*size = ARRAY_SIZE(io_win_memory_map);
+
+	return 0;
+}
+
+#ifndef IMAGE_BLE
+/*****************************************************************************
+ * IOB Configuration
+ *****************************************************************************
+ */
+struct addr_map_win iob_memory_map_cp0[] = {
+	/* CP0 */
+	/* PEX1_X1 window */
+	{0x00000000f7000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000f8000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000f6000000,	0x1000000,	PEX0_TID},
+	{0x00000000c0000000,	0x30000000,	PEX0_TID},
+	{0x0000000800000000,	0x100000000,	PEX0_TID},
+};
+
+struct addr_map_win iob_memory_map_cp1[] = {
+	/* CP1 */
+	/* SPI1_CS0 (RUNIT) window */
+	{0x00000000f9000000,	0x1000000,	RUNIT_TID},
+	/* PEX1_X1 window */
+	{0x00000000fb000000,	0x1000000,	PEX1_TID},
+	/* PEX2_X1 window */
+	{0x00000000fc000000,	0x1000000,	PEX2_TID},
+	/* PEX0_X4 window */
+	{0x00000000fa000000,	0x1000000,	PEX0_TID}
+};
+
+int marvell_get_iob_memory_map(struct addr_map_win **win, uint32_t *size,
+			       uintptr_t base)
+{
+	switch (base) {
+	case MVEBU_CP_REGS_BASE(0):
+		*win = iob_memory_map_cp0;
+		*size = ARRAY_SIZE(iob_memory_map_cp0);
+		return 0;
+	case MVEBU_CP_REGS_BASE(1):
+		*win = iob_memory_map_cp1;
+		*size = ARRAY_SIZE(iob_memory_map_cp1);
+		return 0;
+	default:
+		*size = 0;
+		*win = 0;
+		return 1;
+	}
+}
+#endif
+
+/*****************************************************************************
+ * CCU Configuration
+ *****************************************************************************
+ */
+struct addr_map_win ccu_memory_map[] = {
+#ifdef IMAGE_BLE
+	{0x00000000f2000000,	0x4000000,  IO_0_TID}, /* IO window */
+#else
+	{0x00000000f2000000,	0xe000000,  IO_0_TID}, /* IO window */
+	{0x00000000c0000000,	0x30000000,  IO_0_TID}, /* IO window */
+	{0x0000000800000000,	0x100000000,  IO_0_TID}, /* IO window */
+#endif
+};
+
+uint32_t marvell_get_ccu_gcr_target(int ap)
+{
+	return DRAM_0_TID;
+}
+
+int marvell_get_ccu_memory_map(int ap_index, struct addr_map_win **win,
+			       uint32_t *size)
+{
+	*win = ccu_memory_map;
+	*size = ARRAY_SIZE(ccu_memory_map);
+
+	return 0;
+}
+
+/* In reference to #ifndef IMAGE_BLE, this part is used for BLE only. */
+
+/*****************************************************************************
+ * SKIP IMAGE Configuration
+ *****************************************************************************
+ */
+void *plat_marvell_get_skip_image_data(void)
+{
+	/* No recovery button on A8k-MCBIN board */
+	return NULL;
+}
diff --git a/plat/marvell/a8k/a80x0_mcbin/mvebu_def.h b/plat/marvell/a8k/a80x0_mcbin/mvebu_def.h
new file mode 100644
index 0000000..5bff12c
--- /dev/null
+++ b/plat/marvell/a8k/a80x0_mcbin/mvebu_def.h
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#ifndef __MVEBU_DEF_H__
+#define __MVEBU_DEF_H__
+
+#include <a8k_plat_def.h>
+
+#define CP_COUNT		2	/* A80x0 has both CP0 & CP1 */
+#define I2C_SPD_ADDR		0x53	/* Access SPD data */
+#define I2C_SPD_P0_ADDR		0x36	/* Select SPD data page 0 */
+
+#endif /* __MVEBU_DEF_H__ */
diff --git a/plat/marvell/a8k/a80x0_mcbin/platform.mk b/plat/marvell/a8k/a80x0_mcbin/platform.mk
new file mode 100644
index 0000000..0fe235b
--- /dev/null
+++ b/plat/marvell/a8k/a80x0_mcbin/platform.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2018 Marvell International Ltd.
+#
+# SPDX-License-Identifier:     BSD-3-Clause
+# https://spdx.org/licenses
+#
+
+PCI_EP_SUPPORT		:= 0
+
+DOIMAGE_SEC     	:=	tools/doimage/secure/sec_img_8K.cfg
+
+MARVELL_MOCHI_DRV	:=	drivers/marvell/mochi/apn806_setup.c
+
+include plat/marvell/a8k/common/a8k_common.mk
+
+include plat/marvell/common/marvell_common.mk