diff --git a/plat/marvell/a8k/a80x0/board/dram_port.c b/plat/marvell/a8k/a80x0/board/dram_port.c
new file mode 100644
index 0000000..c720c11
--- /dev/null
+++ b/plat/marvell/a8k/a80x0/board/dram_port.c
@@ -0,0 +1,141 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+#include <arch_helpers.h>
+#include <a8k_i2c.h>
+#include <debug.h>
+#include <mmio.h>
+#include <mv_ddr_if.h>
+#include <mvebu_def.h>
+#include <plat_marvell.h>
+
+#define MVEBU_AP_MPP_CTRL0_7_REG		MVEBU_AP_MPP_REGS(0)
+#define MVEBU_AP_MPP_CTRL4_OFFS			16
+#define MVEBU_AP_MPP_CTRL5_OFFS			20
+#define MVEBU_AP_MPP_CTRL4_I2C0_SDA_ENA		0x3
+#define MVEBU_AP_MPP_CTRL5_I2C0_SCK_ENA		0x3
+
+#define MVEBU_CP_MPP_CTRL37_OFFS		20
+#define MVEBU_CP_MPP_CTRL38_OFFS		24
+#define MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA	0x2
+#define MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA	0x2
+
+#define MVEBU_MPP_CTRL_MASK			0xf
+
+/*
+ * This struct provides the DRAM training code with
+ * the appropriate board DRAM configuration
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	/* MISL board with 1CS 8Gb x4 devices of Micron 2400T */
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X subphys */
+	{ { { {0x1, 0x0, 0, 0},	/* FIXME: change the cs mask for all 64 bit */
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0},
+	      {0x1, 0x0, 0, 0} },
+	   /* TODO: double check if the speed bin is 2400T */
+	   SPEED_BIN_DDR_2400T,		/* speed_bin */
+	   MV_DDR_DEV_WIDTH_8BIT,	/* sdram device width */
+	   MV_DDR_DIE_CAP_8GBIT,	/* die capacity */
+	   MV_DDR_FREQ_SAR,		/* frequency */
+	   0, 0,			/* cas_l, cas_wl */
+	   MV_DDR_TEMP_LOW} },		/* temperature */
+	MV_DDR_64BIT_ECC_PUP8_BUS_MASK, /* subphys mask */
+	MV_DDR_CFG_SPD,			/* ddr configuration data source */
+	{ {0} },			/* raw spd data */
+	{0},				/* timing parameters */
+	{				/* electrical configuration */
+		{			/* memory electrical configuration */
+			MV_DDR_RTT_NOM_PARK_RZQ_DISABLE,	/* rtt_nom */
+			{
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV4, /* rtt_park 1cs */
+				MV_DDR_RTT_NOM_PARK_RZQ_DIV1  /* rtt_park 2cs */
+			},
+			{
+				MV_DDR_RTT_WR_DYN_ODT_OFF,	/* rtt_wr 1cs */
+				MV_DDR_RTT_WR_RZQ_DIV2		/* rtt_wr 2cs */
+			},
+			MV_DDR_DIC_RZQ_DIV7	/* dic */
+		},
+		{			/* phy electrical configuration */
+			MV_DDR_OHM_30,	/* data_drv_p */
+			MV_DDR_OHM_30,	/* data_drv_n */
+			MV_DDR_OHM_30,	/* ctrl_drv_p */
+			MV_DDR_OHM_30,	/* ctrl_drv_n */
+			{
+				MV_DDR_OHM_60,	/* odt_p 1cs */
+				MV_DDR_OHM_120	/* odt_p 2cs */
+			},
+			{
+				MV_DDR_OHM_60,	/* odt_n 1cs */
+				MV_DDR_OHM_120	/* odt_n 2cs */
+			},
+		},
+		{			/* mac electrical configuration */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_pattern */
+			MV_DDR_ODT_CFG_ALWAYS_ON,	/* odtcfg_write */
+			MV_DDR_ODT_CFG_NORMAL,		/* odtcfg_read */
+		},
+	}
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+static void mpp_config(void)
+{
+	uintptr_t reg;
+	uint32_t val;
+
+	reg = MVEBU_CP_MPP_REGS(0, 4);
+	/* configure CP0 MPP 37 and 38 to i2c */
+	val = mmio_read_32(reg);
+	val &= ~((MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_MPP_CTRL_MASK << MVEBU_CP_MPP_CTRL38_OFFS));
+	val |= (MVEBU_CP_MPP_CTRL37_I2C0_SCK_ENA <<
+			MVEBU_CP_MPP_CTRL37_OFFS) |
+		(MVEBU_CP_MPP_CTRL38_I2C0_SDA_ENA <<
+			MVEBU_CP_MPP_CTRL38_OFFS);
+	mmio_write_32(reg, val);
+}
+
+/*
+ * This function may modify the default DRAM parameters
+ * based on information received from SPD or bootloader
+ * configuration located on non volatile storage
+ */
+void plat_marvell_dram_update_topology(void)
+{
+	struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get();
+
+	INFO("Gathering DRAM information\n");
+
+	if (tm->cfg_src == MV_DDR_CFG_SPD) {
+		/* configure MPPs to enable i2c */
+		mpp_config();
+
+		/* initialize i2c */
+		i2c_init((void *)MVEBU_CP0_I2C_BASE);
+
+		/* select SPD memory page 0 to access DRAM configuration */
+		i2c_write(I2C_SPD_P0_ADDR, 0x0, 1, tm->spd_data.all_bytes, 1);
+
+		/* read data from spd */
+		i2c_read(I2C_SPD_ADDR, 0x0, 1, tm->spd_data.all_bytes,
+			 sizeof(tm->spd_data.all_bytes));
+	}
+}