ARM Trusted Firmware for Socionext UniPhier SoCs

Socionext UniPhier ARMv8-A SoCs use ARM Trusted Firmware as the secure world firmware, supporting BL1, BL2, and BL31.

UniPhier SoC family implements its internal boot ROM, so BL1 is used as pseudo ROM (i.e. runs in RAM). The internal boot ROM loads 64KB [1] image from a non-volatile storage to the on-chip SRAM. Unfortunately, BL1 does not fit in the 64KB limit if Trusted Board Boot (TBB) is enabled. To solve this problem, Socionext provides a first stage loader called UniPhier BL. This loader runs in the on-chip SRAM, initializes the DRAM, expands BL1 there, and hands the control over to it. Therefore, all images of ARM Trusted Firmware run in DRAM.

The UniPhier platform works with/without TBB. See below for the build process of each case. The image authentication for the UniPhier platform fully complies with the Trusted Board Boot Requirements (TBBR) specification.

The UniPhier BL does not implement the authentication functionality, that is, it can not verify the BL1 image by itself. Instead, the UniPhier BL assures the BL1 validity in a different way; BL1 is GZIP-compressed and appended to the UniPhier BL. The concatenation of the UniPhier BL and the compressed BL1 fits in the 64KB limit. The concatenated image is loaded by the boot ROM (and verified if the chip fuses are blown).

[1]: Some SoCs can load 80KB, but the software implementation must be aligned to the lowest common denominator.

Boot Flow

  1. The Boot ROM

This is hard-wired ROM, so never corrupted. It loads the UniPhier BL (with compressed-BL1 appended) into the on-chip SRAM. If the SoC fuses are blown, the image is verified by the SoC's own method.

  1. UniPhier BL

This runs in the on-chip SRAM. After the minimum SoC initialization and DRAM setup, it decompresses the appended BL1 image into the DRAM, then jumps to the BL1 entry.

  1. BL1

This runs in the DRAM. It extracts BL2 from FIP (Firmware Image Package). If TBB is enabled, the BL2 is authenticated by the standard mechanism of ARM Trusted Firmware.

  1. BL2, BL31, and more

They all run in the DRAM, and are authenticated by the standard mechanism if TBB is enabled. See Firmware Design for details.

Basic Build

BL1 must be compressed for the reason above. The UniPhier's platform makefile provides a build target bl1_gzip for this.

For a non-secure boot loader (aka BL33), U-Boot is well supported for UniPhier SoCs. The U-Boot image (u-boot.bin) must be built in advance. For the build procedure of U-Boot, refer to the document in the U-Boot project.

To build minimum functionality for UniPhier (without TBB):

make CROSS_COMPILE=<gcc-prefix> PLAT=uniphier BL33=<path-to-BL33> bl1_gzip fip

Output images:

  • bl1.bin.gzip
  • fip.bin

Optional features

  • Trusted Board Boot

mbed TLS is needed as the cryptographic and image parser modules. Refer to the User Guide for the appropriate version of mbed TLS.

To enable TBB, add the following options to the build command:

  TRUSTED_BOARD_BOOT=1 GENERATE_COT=1 MBEDTLS_DIR=<path-to-mbedtls>
  • System Control Processor (SCP)

If desired, FIP can include an SCP BL2 image. If BL2 finds an SCP BL2 image in FIP, BL2 loads it into DRAM and kicks the SCP. Most of UniPhier boards still work without SCP, but SCP provides better power management support.

To include SCP_BL2, add the following option to the build command:

  SCP_BL2=<path-to-SCP>
  • BL32 (Secure Payload)

To enable BL32, add the following option to the build command:

  SPD=<spd> BL32=<path-to-BL32>

If you use TSP for BL32, BL32=<path-to-BL32> is not required. Just add the following:

  SPD=tspd