poplar: Enable emmc support
Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
diff --git a/plat/hisilicon/poplar/include/hi3798cv200.h b/plat/hisilicon/poplar/include/hi3798cv200.h
index 540d0aa..125b048 100644
--- a/plat/hisilicon/poplar/include/hi3798cv200.h
+++ b/plat/hisilicon/poplar/include/hi3798cv200.h
@@ -7,6 +7,8 @@
#ifndef __HI3798cv200_H__
#define __HI3798cv200_H__
+#include <utils_def.h>
+
/* PL011 */
#define PL011_UART0_BASE (0xF8B00000)
#define PL011_BAUDRATE (115200)
@@ -63,11 +65,11 @@
#define EMMC_CLK_50M (1 << 8)
#define EMMC_CLK_25M (2 << 8)
-#define EMMC_DESC_SIZE (0xF0000)
+#define EMMC_DESC_SIZE U(0x00100000) /* 1MB */
#define EMMC_INIT_PARAMS(base) \
{ .bus_width = EMMC_BUS_WIDTH_8, \
.clk_rate = 25 * 1000 * 1000, \
- .desc_base = (base) - EMMC_DESC_SIZE, \
+ .desc_base = (base), \
.desc_size = EMMC_DESC_SIZE, \
.flags = EMMC_FLAG_CMD23, \
.reg_base = REG_BASE_MCI, \
diff --git a/plat/hisilicon/poplar/include/platform_def.h b/plat/hisilicon/poplar/include/platform_def.h
index 3d1ad9b..c0f8371 100644
--- a/plat/hisilicon/poplar/include/platform_def.h
+++ b/plat/hisilicon/poplar/include/platform_def.h
@@ -12,6 +12,7 @@
#include <gic_common.h>
#include <interrupt_props.h>
#include <tbbr/tbbr_img_def.h>
+#include <utils_def.h>
#include "hi3798cv200.h"
#include "poplar_layout.h" /* BL memory region sizes, etc */
@@ -53,13 +54,12 @@
#define POPLAR_DRAM_ID 1
/*
- * DDR for OP-TEE (28MB from 0x02200000 -0x04000000) is divided in several
+ * DDR for OP-TEE (26MB from 0x02400000 -0x04000000) is divided in several
* regions:
* - Secure DDR (default is the top 16MB) used by OP-TEE
* - Non-secure DDR (4MB) reserved for OP-TEE's future use
* - Secure DDR (4MB aligned on 4MB) for OP-TEE's "Secure Data Path" feature
* - Non-secure DDR used by OP-TEE (shared memory and padding) (4MB)
- * - Non-secure DDR (2MB) reserved for OP-TEE's future use
*/
#define DDR_SEC_SIZE 0x01000000
#define DDR_SEC_BASE 0x03000000
@@ -96,6 +96,11 @@
#endif /* SPD_none */
#endif
+#define POPLAR_EMMC_DATA_BASE U(0x02200000)
+#define POPLAR_EMMC_DATA_SIZE EMMC_DESC_SIZE
+#define POPLAR_EMMC_DESC_BASE (POPLAR_EMMC_DATA_BASE + POPLAR_EMMC_DATA_SIZE)
+#define POPLAR_EMMC_DESC_SIZE EMMC_DESC_SIZE
+
#define PLAT_POPLAR_NS_IMAGE_OFFSET 0x37000000
/* Page table and MMU setup constants */
diff --git a/plat/hisilicon/poplar/include/poplar_layout.h b/plat/hisilicon/poplar/include/poplar_layout.h
index e0b5618..3e11370 100644
--- a/plat/hisilicon/poplar/include/poplar_layout.h
+++ b/plat/hisilicon/poplar/include/poplar_layout.h
@@ -12,8 +12,8 @@
*/
/*
- * When Poplar is powered on, boot ROM loads the initial content of
- * boot media into low memory, verifies it, and begins executing it
+ * When Poplar is powered on, boot ROM verifies the initial content of
+ * boot media, loads it into low memory, and begins executing it
* in 32-bit mode. The image loaded is "l-loader.bin", which contains
* a small amount code along with an embedded ARM Trusted Firmware
* BL1 image. The main purpose of "l-loader" is to prepare the
@@ -78,12 +78,27 @@
#define BL1_OFFSET 0x0000D000 /* page multiple */
#define FIP_BASE 0x02040000
+/*
+ * FIP_BASE_EMMC = 0x40000 - 0x1000
+ * = fip.bin offset - l-loader text offset
+ * in l-loader.bin
+ */
+#define FIP_BASE_EMMC 0x0003f000
+
#define BL1_RO_SIZE 0x00008000 /* page multiple */
#define BL1_RW_SIZE 0x00008000 /* page multiple */
#define BL1_SIZE (BL1_RO_SIZE + BL1_RW_SIZE)
#define BL2_SIZE 0x0000c000 /* page multiple */
#define BL31_SIZE 0x00014000
-#define FIP_SIZE 0x000c0000 /* absolute max */
+/*
+ * emmc partition1 4096KB
+ * - l-loader.bin 1984KB
+ * |- l-loader + bl1.bin 256KB
+ * |- fip.bin 1728KB (0x001b0000)
+ * - u-boot persistent data 64KB
+ * - uefi persistent data 2048KB
+ */
+#define FIP_SIZE 0x001b0000 /* absolute max */
/* BL1_OFFSET */ /* (Defined above) */
#define BL1_BASE (LLOADER_TEXT_BASE + BL1_OFFSET)