diff --git a/drivers/brcm/emmc/emmc_chal_sd.c b/drivers/brcm/emmc/emmc_chal_sd.c
index 34d761c..5379ec1 100644
--- a/drivers/brcm/emmc/emmc_chal_sd.c
+++ b/drivers/brcm/emmc/emmc_chal_sd.c
@@ -119,7 +119,7 @@
 		mmio_setbits_32(handle->ctrl.sdRegBaseAddr + SD4_EMMC_TOP_CTRL_OFFSET,
 				SD4_EMMC_TOP_CTRL_SDPWR_MASK);
 
-	/* dummy write & ack to verify if the sdio is ready to send commads */
+	/* dummy write & ack to verify if the sdio is ready to send commands */
 	mmio_write_32(handle->ctrl.sdRegBaseAddr + SD4_EMMC_TOP_ARG_OFFSET, 0);
 	mmio_write_32(handle->ctrl.sdRegBaseAddr + SD4_EMMC_TOP_CMD_OFFSET, 0);
 
@@ -600,7 +600,7 @@
 
 	if (actual_freq > desired_freq) {
 		/*
-		 * Division does not result in exact freqency match.
+		 * Division does not result in exact frequency match.
 		 * Make sure resulting frequency does not exceed requested freq.
 		 */
 		div_ctrl_setting++;
diff --git a/drivers/brcm/emmc/emmc_csl_sdcard.c b/drivers/brcm/emmc/emmc_csl_sdcard.c
index 40bc4a0..789ed9c 100644
--- a/drivers/brcm/emmc/emmc_csl_sdcard.c
+++ b/drivers/brcm/emmc/emmc_csl_sdcard.c
@@ -244,7 +244,7 @@
  * The function handles real data transmission on both DMA and
  * none DMA mode, In None DMA mode the data transfer starts
  * when the command is sent to the card, data has to be written
- * into the host contollers buffer at this time one block
+ * into the host controllers buffer at this time one block
  * at a time.
  * In DMA mode, the real data transfer is done by the DMA engine
  * and this functions just waits for the data transfer to complete.
@@ -318,7 +318,7 @@
 
 
 /*
- * The function initalizes the SD/SDIO/MMC/CEATA and detects
+ * The function initializes the SD/SDIO/MMC/CEATA and detects
  * the card according to the flag of detection.
  * Once this function is called, the card is put into ready state
  * so application can do data transfer to and from the card.
@@ -393,7 +393,7 @@
 
 
 /*
- * The function handles MMC/CEATA card initalization.
+ * The function handles MMC/CEATA card initialization.
  */
 int init_mmc_card(struct sd_handle *handle)
 {
diff --git a/drivers/brcm/i2c/i2c.c b/drivers/brcm/i2c/i2c.c
index 2096a82..b45c0e7 100644
--- a/drivers/brcm/i2c/i2c.c
+++ b/drivers/brcm/i2c/i2c.c
@@ -612,7 +612,7 @@
  *
  * Description:
  *	This function reads I2C data from a device without specifying
- *	a command regsiter.
+ *	a command register.
  *
  * Parameters:
  *	bus_id  - I2C bus ID
@@ -647,7 +647,7 @@
  *
  * Description:
  *	This function send I2C data to a device without specifying
- *	a command regsiter.
+ *	a command register.
  *
  * Parameters:
  *	bus_id  - I2C bus ID
diff --git a/drivers/brcm/sotp.c b/drivers/brcm/sotp.c
index 63c4820..20c6441 100644
--- a/drivers/brcm/sotp.c
+++ b/drivers/brcm/sotp.c
@@ -168,7 +168,7 @@
 	       BIT(SOTP_STATUS__FDONE))
 		;
 
-	/*  Enable OTP acces by CPU */
+	/*  Enable OTP access by CPU */
 	mmio_setbits_32(SOTP_PROG_CONTROL,
 			BIT(SOTP_PROG_CONTROL__OTP_CPU_MODE_EN));
 
@@ -244,7 +244,7 @@
 	/* Command done is cleared w1c */
 	mmio_setbits_32(SOTP_STATUS_1, BIT(SOTP_STATUS_1__CMD_DONE));
 
-	/* disable OTP acces by CPU */
+	/* disable OTP access by CPU */
 	mmio_clrbits_32(SOTP_PROG_CONTROL,
 			BIT(SOTP_PROG_CONTROL__OTP_CPU_MODE_EN));